background image

8

Buffalo Technology

Technical Support

Buffalo Technology offers  Toll-Free Technical Support 24 hours a day, 7 days a week

for this product. Customers in the United States and Canada can obtain technical

support using the following information:

◗ 

Online Help

Available on the AirNavigator CD enclosed with your purchase.

Web

www.buffalotech.com/wireless

E-mail

info@buffalotech.com 

Telephone

866-752-6210

(USA & Canada only)

The constantly evolving state of wireless products and operating systems requires

Buffalo Technology to occasionally release updated software to take advantage of

new technologies and to comply with industry standards.For the most recent software,

firmware, driver, and technical whitepaper releases available, please visit the Buffalo

Technology website.

FCC Compliance Statement - 

See owners manual for complete statement.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

R&TTE Compliance Statement - 

See owners manual for complete statement.

This equipment complies with all the requirements of the DIRECTIVE 1999/5/EC OF THE

EUROPEAN PARLIAMENT AND THE COUNCIL of 9 March 1999 on radio equipment and

telecommunication terminal Equipment and the mutual recognition of their conformity

(R&TTE).

Copyright © 2003 Buffalo Technology, Inc. All Rights Reserved.
Buffalo Technology (USA) Inc., is part of MELCO INC., the global manufacturers of IT peripherals, including memory, networking,
and multimedia products, inside many of the world's computers. All trademarks are property of their respective owners.

Summary of Contents for AirStation G54 WLA2-G54









Reviews: