Buffalo CD963 Instruction Manual Download

Page: 2 / 20

Contents

Gas Griddle

CD963

Gas Griddle

CD964

Gas Griddle

Introduction ............................................................................................. 2

Specifications ........................................................................................... 3

Model Numbers Covered in this Specification
General
Gas Supply Requirements
Gas Connection

Dimensions ................................................................................................ 4

Installation ................................................................................................ 5

Installation Requirements
Unpacking
Location
Clearances
Assembly
Gas Connection
Commissioning

Operation ................................................................................................. 8

Operation Guide
Description of Controls
Lighting the Pilot Burner
Lighting the Main Burner

Cleaning and Maintenance ......................................................................... 10

Routine Maintenance
After Each Use
Daily Cleaning
Weekly Cleaning

Trouble Shooting.......................................................................................12

Gas Conversion and Specifications .............................................................. 13

Conversion Procedure
Gas Specifications

Replacement Parts List ..............................................................................17

Explosion Drawing ..............................................................................……18

Spare Parts List .............................................................................. .........19

Summary of Contents for CD963





















Search results

Summary of Contents for CD963

Reviews:

Related manuals for CD963

Brands by name

Popular brands

Buffalo CD963, Instruction Manual

Search results

Summary of Contents for CD963

Reviews:

Related manuals for CD963

Brands by name

Popular brands