background image

1

®

Quick Setup Guide

54

 

Mbps

*

 Wireless Bridge Base Station-g

WLA-G54

Preparation

This  Quick  Setup  Guide  will  guide  you 

through  quickly  and  easily  installing  this 

product on your Windows PC.  For detailed 

setup and configuration instructions, please 

refer to the User Manual on the Utility CD or 

the Buffalo Wireless Support website.

Package Contents:

◗ 

54

 

Mbps

*

 Bridge Base Station

◗ 

Utility CD-ROM 

◗ 

Quick Setup Guides

◗ 

AC Adapter 

◗ 

7ft.

 

Ethernet Cable

◗ 

Warranty Statement

If any of the contents are missing, please 

contact the reseller from which this prod-

uct was purchased.

System Requirements

◗ 

Desktop  or  laptop  PC  with  a

   wireless adapter installed.

◗ 

Existing Local Area Network to 

   connect to the 

AirStation

 

54

 

Mbps

*

  

   

Bridge Base Station

.

There are 2 methods of configuring your 

AirStation  54

 

Mbps

*

 

Bridge  Base 

Station

.  Depending  on  the  configura-

tion of the computer you will be using to 

configure your access point, choose the 

method  to  configure  the 

AirStation 

54

 M

bps

*

 Bridge Base Station

.

www.buffalotech.com/

PY00-11001-DM20 Rev A

Summary of Contents for WLA-G54









Reviews: