LIGHTING & OPERATING INSTRUCTIONS
LIGHTING PROCEDURES
Lighting Main Burner(s):
1. Become familiar with safety guidelines at front of manual.
DO NOT SMOKE WHILE LIGHTING GRILL OR
CHECKING GAS SUPPLY CONNECTIONS.
2. If your
grill fuel source is an LP gas cylinder, check to see that cylinder is filled.
3. Check the end of each burner tube is properly located over each valve orifice.
4. Make sure all gas connections are securely tightened.
TEST FOR LEAKS WITH A SOAP SOLUTION, NEVER WITH
A
FLAME
. (Gas Leak Check instructions are on page 2).
5. Always open lid before lighting.
6. Set ALL BBQ Grill control knobs to “OFF” and open gas supply, LP cylinder or Natural Gas Valve.
7. Ignite only the burners you intend to use, using the same method for each: Push in control knob fully and rotate
slowly (3 to 4 seconds) about 1/4
turn to the left (counter clockwise) until a click is heard. The 3 to 4 second
duration should provide enough gas to light the burner. If the burner does not light, immediately return the control
knob to “OFF”, wait several minutes for the gas to disperse, and repeat the process. After burner ignites, repeat
procedure with any other burner needed.
8.
Adjust control knob(s) to desired cooking temperature.
NOTE:
If for some reason, igniters fail to produce a spark at the electrode tip, burners can be lit with a match.
NOTE:
To light gas grill with a match
, follow steps 1 through 6 above. Remove cooking grid and flame tamer from
burner you wish to light. Insert lighted fireplace-type match or long-necked butane lighter placing flame near to burner
ports. Press in control knob and rotate left to “HI” setting to release gas. Burner should light immediately. If more than one
burner is needed, repeat procedure with each burner. Replace flame tamer and cooking grid. Turn off burners not needed,
and adjust other burners to desired cooking temperature.
Lighting Rotisserie Burner (if equipped):
The rear infrared rotisserie burner allows for slow rotisserie cooking of meats and poultry. Infrared burners radiate heat
onto the outer surface of the food. This allows cooking without the grease drippings burning on the flame tamers.
To light Rotisserie Burner
,
1. Always open lid before lighting.
2.
Set ALL BBQ Grill control knobs to “OFF” and open gas supply, LP cylinder or Natural Gas Valve.
3.
The Control knob is located at the middle of the Control Panel. Push in control knob fully and rotate slowly (3 to 4
seconds) about 1/4
turn to the left (counter clockwise) until a click is heard. The 3 to 4 second duration should provide
enough gas to light the burner. If the burner does not light, immediately return the control knob to “OFF”, wait several
minutes for any accumulated gas to clear out of the grill. Keep lid closed and operate burner at the “ON” position when
rotisserie cooking.
WARNING: Never operate Rotisserie Burner with main (other) burner(s) ON
Warming Rack must be removed when Rotisserie Burner is ON
Do not attempt to regulate the rotisserie burner by using the control knob. This control has a fixed setting and is
not adjustable.
NOTE
: Initially, the Ceramic Panel will have a blue flame that, after some time, will change to an orange flame and the
Ceramic Panel will glow an orange color.
This may not be evident in bright daylight.
To light
Rotisserie Burner
with a match
, Follow steps 1 through 2 above. Insert lighted fireplace-type match or long-
necked butane lighter placing flame near to the Ceramic Panel. Press in control knob and rotate left (counter clockwise) to
“HI” or “ON” setting to release gas. Burner should light immediately.
11
Summary of Contents for Texan Lonestar 07638
Page 17: ...ILLUSTRATED PARTS LIST 17 ...
