background image

HOW TO ORDER REPLACEMENT PARTS

                                                                               

Please refer to the parts list.
To make sure you obtain the correct replacement parts for your gas grill, the following information is required to 
assure getting the correct part.

1. Gas grill model number (see data sticker on grill) and type of gas hook up. 
2. Reference number of replacement part needed.
3. Description of replacement part needed
4. Quantity of parts needed.

IMPORTANT:

 Use only factory authorized parts. The use of any part that is not factory authorized 

can 

be 

dangerous. This will also void your warranty.

IMPORTANT:

 Keep this assembly and operating instruction manual for referral and for

 

replacement parts ordering.

CAUTION:

 Gas valves are preset at the factory. If you wish to convert at some later date, be sure to contact your 

gas supplier or grill dealer before making the conversion.

CAUTION:

 A different gas valve must be installed when converting from one type of gas to another. You will also 

need a data plate indicating what type of gas the grill uses.

16

Summary of Contents for Texan Lonestar 07638



















Reviews: