Bullard GenVX Series User Manual Download

Page: 24 / 28

Ordering

Information

Parts and Accessories for GenVX Series Airline Respirators

GenVX Series supplied-air respirators consist of four components: 1.) respirator helmet assembly with breathing tube, 2.) cape, 3.) flow control
device, and 4.) air supply hose. There are options for some components to fit customer specifications. All components must be present and properly
assembled, including a Bullard air supply hose, to constitute a complete NIOSH approved respirator (Approval No. TC-19C-0489, TC-19C-0491,
TC-19C-0492, TC-19C-0493, TC-19C-0494, TC-19C-0495, TC-19C-0496, TC-19C-0498, Type C and CE).

CATALOG

NUMBER DESCRIPTION

GenVX Bundles

GVX2830

28” Cape Assembly with Continuous Flow Control

GVX2830AC1000 28” Cape Assembly with AC1000 Cool Tube
GVX2830CT

28” Cape Assembly with CT Cool Tube

GVX2830HC2400 28” Cape Assembly with HC2400 Hot/Cold Tube
GVX2830HCT

28” Cape Assembly with HCT Hot/Cold Tube

GVX2831AC1000 28” Cape Assembly with AC1000 Cool Tube,

Schrader Fitting

GVX2831CT

28” Cape Assembly with CT Cool Tube, Schrader Fitting

GVX2835

28” Cape Assembly for use with Ambient Air Pump

GVX2840

28” Cape Assembly with Adjustable Flow Control

GVX3830

38” Cape Assembly with Continuous Flow Control

GVX3830AC1000 38” Cape Assembly with AC1000 Cool Tube
GVX3830CT

38” Cape Assembly with CT Cool Tube

GVX3830HC2400 38” Cape Assembly with HC2400 Hot/Cold Tube
GVX3830HCT

38” Cape Assembly with HCT Hot/Cold Tube

GVX3835

38” Cape Assembly for use with Ambient Air Pump

GVX3840

38” Parka Assembly with Adjustable Flow Control

GVXPK30AC1000 38” Parka Assembly with AC1000 Cool Tube
GVXPK30CT

38” Parka Assembly with CT Cool Tube

GVXPK30HC2400 38” Parka Assembly with HC2400 Hot/Cold Tube
GVXPK30HCT

38” Parka Assembly with HCT Hot/Cold Tube

GVXPK30XLCT

38” Parka XL Assembly with CT Cool Tube

GVXPK40

38” Cape Assembly with Adjustable Flow Control

GVXGG30

38” Golden Gate with Cap Sleeves and Constant Flow
Control

Parts for GenVX Series Respirators

GVXRT

Ratchet Suspension

GVXCS

Elastic Chin Strap

GVXCT

Breathing tube connector kit

GVXDMK

Door maintenance kit

GVXHP

Hinge pin

GVXIG

Replacement inner gasket

GVXFP

Replacement foam airline plug (10 pack)

Accessories

GVXCA

Carrying assembly

GVXPL

Pinlock suspension

RBPCOTTON

Cotton brow pad

RBPCOOL Polartec

brow pad

RBPVINYL

Vinyl brow pad

GVXCP

Cheek pads

Lenses and Mylar Covers

Inner Lenses

GVXIL

Inner Tritan Lens, .040” thick (25/pkg)

Outer Lenses

GVXOL40

Outer PETG Lens, .040” thick (25/pkg)

GVXOL15

Outer PETG Lens, .015” thick (50/pkg)

BGVXOL40

Outer PETG Lens, .040” thick (200/bx)

BGVXOL15

Outer PETG Lens, .015” thick (200/bx)

GVXOLT

Outer Lenses, .030”, pack of 25 Tinted (Smoke)

GVXOLG

Outer Lenses .042”, pack of 25 Tinted (Green)

Lens Cover

GVXLC

Mylar lens cover, adhesive-backed, 25 pk

Capes

28VX

Tan Nylon Cape - 28” length

38VX

Tan Nylon Cape - 38” length

GGVX

Tan Nylon Cape, Golden Gate Style - 38” length

PKVX

Hibernia Parka -Tan Nylon Parka

with sleeves - 38” length

PKXLVX

Hibernia Parka - Tan Nylon Parka

with sleeves - 38” length, extra-large

Flow Control Devices (Includes Belt)

F30

Constant flow control valve,

1/4” Industrial Interchange (steel)

F35

Constant flow control valve,
1/2” Industrial Interchange (steel)

F40

Adjustable flow control tube valve - 1/4” Industrial

Interchange (steel) quick-disconnect fitting

CT30

Air Conditioner - 1/4” Industrial Interchange

(steel) quick-disconnect fitting

Frigitron 2000

Air Conditioner - 1/2” Industrial Interchange

(steel) quick-disconnect fitting, (for use with

Bullard EDP30 or ADP20 Free-Air pump)

AC1000

Air Conditioner - 1/4” Industrial Interchange (steel) quick-
disconnect fitting (metal components)

HC2400

Hot/Cold tube - 1/4” Industrial Interchange (steel) quick-
disconnect fitting (metal components)

HCT30

Hot/Cold tube - 1/4” Industrial Interchange

(steel) quick-disconnect fitting

DC5040

DUAL-COOL tube - 1/4” Industrial Interchange

(steel) quick disconnect fitting. Order DUAL-COOL vest
separately

Dual-Cool Vest

DC70ML

DUAL-COOL vest. Size: M/L. Order DUAL-COOL

tube separately.

DC70XLXXL

DUAL-COOL vest. Size: XL/XXL. Order DUAL-COOL

tube separately.

DC705X

DUAL-COOL vest. Size: 5XL. Order DUAL-COOL

tube separately.

CH60

Connector hose for use with DUAL-COOL

Replacement Parts for Breathing Tube Assemblies

GVXBT

Breathing tube only, with threaded hose connectors

4612

Belt, nylon webbing

36501

Belt, vinyl

GVXBTW

Breathing tube washer (10 pack, red)

Air Supply Hose Kits

V10 Series Hoses (3/8” I.D.) for use with breathing air compressors

4696

25-foot Starter hose with 1/4”

Industrial Interchange Q.D. coupler and male nipple

46913

25-foot Starter hose with 1/4”

Schrader Q.D. coupler

46915

25-foot Starter hose with 1/4”

Snap-Tite Q.D. coupler

469650

50-foot Starter hose with 1/4” Industrial Interchange Q.D.

coupler and male nipple

4696100

100-foot Starter hose with 1/4” Industrial Interchange Q.D.
coupler and male nipple

5454

25-foot Extension hose

5457

50-foot Extension hose

5458

100-foot Extension hose

Summary of Contents for GenVX Series





























Search results

Summary of Contents for GenVX Series

Reviews:

Related manuals for GenVX Series

Brands by name

Popular brands

Bullard GenVX Series, User Manual

Search results

Summary of Contents for GenVX Series

Reviews:

Related manuals for GenVX Series

Brands by name

Popular brands