background image

Return Authorization

The following steps must be completed before Bullard will accept any returned goods. Please read carefully.
Follow the steps outlined below to return goods to Bullard for repair or replacement under warranty or for paid repairs:
1. Contact Bullard Customer Service by telephone or in writing at:
 

Bullard

 

1898 Safety Way

 

Cynthiana, KY 41031-9303

 

Toll-free: 877-BULLARD (285-5273)

 

Phone: 859-234-6616

In your correspondence or conversation with Customer Service, describe the problem as completely as possible. For your convenience, your Customer Service 
specialist will try to help you correct the problem over the phone.
2. Verify with your Customer Service specialist that the product should be returned to Bullard. Customer Service will provide you with written permission and a 
return authorization number as well as the labels you will need to return the product.
3. Before returning the product, decontaminate and clean it to remove any hazardous materials which may have settled on the product during use. Laws and/or 
regulations prohibit the shipment of hazardous or contaminated materials. Products suspected to be contaminated will be professionally discarded at the 
customer’s expense.
4. Ship returned products, including those under warranty, with all transportation charges pre-paid. Bullard cannot accept returned goods on a freight collect 
basis.
5. Returned products will be inspected upon return to the Bullard facility. Bullard Customer Service will telephone you with a quote for required repair work 
which is not covered by warranty. If the cost of repairs exceeds stated quote by more than 20%, your Customer Service specialist will call you for authorization 
to complete repairs. After repairs are completed and the goods have been returned to you, Bullard will invoice you for actual work performed.

Americas:

E.D. Bullard Company

1898 Safety Way  
Cynthiana, KY  41031-9303
Toll free: 877-BULLARD (285-5273)
Tel: 859-234-6616 
Fax: 859-234-8987

www.bullard.com

Europe:

Bullard GmbH

Lilienthalstrasse 12
53424 Remagen • Germany
Tel: +49-2642 999980 
Fax : +49-2642 9999829

www.bullardextrem.com

Asia-Pacific:

Bullard Asia Pacific Pte. Ltd.

LHK Building
701, Sims Drive, #04-03 
Singapore 387383
Tel: +65-6745-0556 
Fax: +65-6745-5

www.bullard.com

©2011 Bullard. All rights reserved.

6081256210D (1011)

ISO 9001 

certified

Parts and Accessories

Adjustable Cool Tubes

Cold Only 

Hot/Cold 

Dual-Cool 

Coupling Type

AC100030 

HC240030 

DC5040 

1/4” Industrial Interchange 

1/4” Snap-Tite, steel

AC100030B 

HC240030B 

DC5040B 

1/4” Industrial Interchange (Brass) 

1/4” Snap-Tite, brass

AC100030S 

HC240030S 

DC5040S 

1/4” Industrial Interchange (Stainless Steel) 

1/4” Snap-Tite,  stainless steel

AC100031 

HC240031 

DC5041 

1/4” Schrader 

 

AC100032  HC240032 DC5042 

 

AC100033  

HC240033 

DC5043

AC100034  

HC240034 

DC5044

FRIGITRON2000
FRIGITRON2000B

V5 Coiled Hose

V52530, V55030, 

V52531, V55031, 

V52532, V55032

Air Supply Hose

4696,46913, 46915,  

5454, 5457, 5458

Summary of Contents for RT Series













Reviews: