background image

2

1 �����READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE OPERATING THE EZ SHEAR

� 

2 �����If you are not thoroughly familiar with the operation of the EZ Shear

, obtain advice from a 

qualified instructor or call 800-406-8998 (Intl.: 208-772-0175). 

3 �����Stay alert. Do not operate while under the influence of drugs, alcohol, or medication.

4 �����Always wear safety approved eye protection with side shields (ANSI Z87.1).

5 �����Keep work area clean and free of debris.

6 �����Recommended operating temperature range: 20° F (-6° C) to 115° F (46° C)

7 �����Keep children and unauthorized persons away from the EZ Shear

 and work area.

8 �����Make sure tool is secure. Operate only on a firm surface or solid stand.

9 �����Use  the  right  tool.  Do  not  force  the  EZ  Shear

  or  use  it  for  a  job  for  which  it  was  not 

intended; the EZ Shear

 is designed to cut residential grade/ low-pressure laminate flooring, 

engineered  wood  flooring,  VCT,  PVC  tile,  vinyl  tile,  fiber  cement  board  siding,  vinyl  siding, 

& pressboard lap siding.  See Cut Guide page 6.

10 ���Keep Blade sharp. A dull Blade will not perform properly.

11 ���Always keep hands away from Blade while operating or carrying.

12 ���Do not alter or misuse this tool. The EZ Shear™ is precision built; modifications not specified in 

this manual may result in a dangerous condition.

13 ���Maintain EZ Shear

 with care. Keep Blade sharp and clean. Follow instructions for lubricating 

and changing accessories. See page 6.

14 ���Use only recommended accessories. The use of improper accessories may cause hazards or 

injury.

15 ���Never leave the EZ Shear

 unattended. Secure the Handle with the Safety Lock when not in 

use. See page 5.

16 ���Warning: The dust generated by cutting certain wood, wood fiber and/or PVC products can 

be hazardous to your health. The EZ Shear

 generally does not produce any dust; however, 

minimal creation of dust may be possible. Avoid ingesting any dust created through cutting.

SAFETY GUIDE FOR THE 

EZ SHEAR

 SST SERIES

WARNING: FAILURE TO FOLLOW THIS GUIDE MAY RESULT IN SERIOUS 

INJURY! USING THIS MACHINE WITH RESPECT AND CAUTION WILL 

CONSIDERABLY REDUCE THE RISK OF PERSONAL INJURY.

Summary of Contents for EZ Shear SST220









Reviews: