background image

During the lasting circulation cleaning,press”

” key can stop the heating ,but start again the heating.

13

Operation of spa lights

Press the

 “

” 

key to turn ON/OFF of the the LED lights and the Fiber optic lights.

14

Setting the constant Temperature Settings

1

)、

Pressing the

 “

 button will start the constant temperature heating.

2

With the setting above, the circulation pump will work automatically.

3

)、

If the temperature is set at 35 ,  when the water temperature reaches or exceeds 36,  the heater

will be turned off automatically and the circulation pump will stop after 5 seconds. When the water temperature
reaches or lower than 34 ,  the heater will start up

 again.

4

)、

In the case of an error the LCD shows ”E1” or “FF”.  If this happens, the thermostatic heating sytem

will NOT be available, the heater doesn’t work.

15

Operating the Air Blower

Press

 controls the blower

16

Fahrenheit & Celsius Temperature shift

In the status of

“Power off” pressing the key

 “

” can change the mode of 

Fahrenheit & Celsius degree

17

When there is no water in the spa. All surfing pumps, and heating system can not

start up. However the corresponding signals will flash on the LCD.

18

Prevent freezing function:

This function is only available while the spa is on normal power supply.The heater & circulation pump will work
automatically once the water temperature is at below 5 ,  when the water temperature is reach at 10,  heating

will stop.

IV

Electric parameters

1

Performance index

Rated voltage

 220V/50Hz                        

Maximum working current

60 A/220

V-240V~

Voltage-resistance

1250V/1

 minute without penetration

     

Isolative resistance

:》

200MΩ

Water resistance grade

IPX5                             

Electric shock resistance

first grade

(2) Output loading index

Heater

 AC220V/3KW     

  

                          Water pump

 AC220V/3H

P×2

  

water pump

AC220V/1H

P

×1 

                           

Air pump

AC220V/700W

×1

    

Spa light

 AC12V/5W                                   Ozone

 AC12V/15W 

Radio

 1) Frequency Range

 FM

 87.0~108.0MHz

        2) Maximum Output Power

 10W

3) Speaker

8Ωdamp proof speaker

10

Summary of Contents for SPA-562
















Reviews: