03
04
The arms and their unique design assist with the lifting of the tent and ensures that it is rigid
when open, essentially strengthening the construction. Unclip both latches and ensure that
they are open before lifting the roof slightly to start the automatic lift of the roof.
OUR TENTS HAVE A ONE YEAR MECHANICAL WARRANTY. All the electronics used in the Bundu-
Clam can be found inside the Electronics Box which houses:
• The fuse
• Switches for the fans and light.
• 12v Socket
If installing on load bars use three evenly spaced supports. Remember to mount the ladder
bracket. After installing the tent, mount the ladder bracket beneath the opening you will be
using as the door. This way the ladder has a place to hook on to and will be less damaging than
simply hooking the ladder onto the lip of the tent. Hold the bracket in position on the side of
the tent where you will be entering your tent. Lightly trace the outline and mounting holes of
the bracket. Mark where you want to place your rivets and drill the holes. Hold the bracket in
place again and rivet the bracket to the tent’s side. Repeat steps for the other bracket.
Maintenance:
While unnecessary when not experiencing any faults, we do recommend maintenance in the
tents.
1. Tent does not go up or down. Check that nothing is caught in the arms.
2. Tent opens but does not close. Check that the main arms are unlocked.
3. The tent doesn’t open. Pick up the roof by hand and lock the arms in place to keep the roof
up.
4. Arms don’t lock. Adjust the tension on the bottom of the arm until the arms lock into place
and extends the Awning.
What is it made from?
The tent is full aluminium construction and a durable Riptech canvas. The tent seals completely
when closed and gives a full dust and waterproof seal. We use a 300gsm Riptech canvas that
is UV resistant to prevent fading. The wrap-around awning is at an angle so that you can have
ventilation in poor weather with maximum water deflection. Our mesh is coated in a rubber
compound making it extremely flexible and durable.
The foam backed roof lining absorbs moisture and condensation but if you are going to ex-
tremely cold areas we do recommend putting a carpet as insulation under the mattress as very
cold temperatures creates additional condensation. The frame built into the bottom of the tent
provides additional strength and makes it versatile to mount. It can be bolted directly to your
load bars or roof rack.
!
Quick Tip:
Taking care of your canvas is easy! Gently wash with a mild detergent and
water. Avoid excessive scrubbing or abrasion.
Can I fit the tent myself ?
Yes. It is not heavy, but it is an awkward shape and will need atleast 2 people to handle.
The holes in my tent doesn’t have eyelets in them. The eyelets don’t wear well. The holes are
actually burned into the canvas, because it’s the strongest way to make the holes. While eyelets
make for a better finish, it does not make for a stronger one, and our research suggests that
eyelets pose as a weak point and is generally where tears can originate. This is caused by the
crimping tool used to install the eyelet, causing its metal edges to essentially cut into the materi-
al it’s being installed in, weakening the material on those points
What Is Covered with the warranty?
BunduTec (Pty) Ltd warrants to the original purchaser that its products are free from defects
in material and workmanship, for the term described, except as qualified below. The life of the
product is determined from the date of purchase until such time as the product is no longer
serviceable due to normal wear and tear. What Is Not Covered BunduTec (Pty) Ltd shall not be
responsible for the natural breakdown of materials that occurs inevitably with extended use
(e.g., Ultra Violet (UV) light damage on tents, exhausted zippers), or defects caused by accident,
abuse, alteration, animal attack, storm damage, misuse or improper care. There are no other
express warranties beyond the terms of this limited warranty. In no event shall BunduTec
(Pty) Ltd be liable for incidental or consequential damages. What BunduTec (Pty) Ltd Will Do
If, after inspection, we find that a product failed due to a manufacturing or material defect,
we will repair or replace the product, at our option, without charge. How To Obtain Warranty
Service Return the product, freight prepaid, to the BunduTec (Pty) Ltd dealer from whom it
was purchased; or contact BunduTec (Pty) Ltd Customer Satisfaction Department for return
authorisation on 063 872 7667. Collect shipments or shipments without return authorisation
cannot be accepted. Repairs If your BunduTec (Pty) Ltd product needs service or repair due to
normal wear and tear, animal attack, accident or some other reason that is not covered under
the warranty we will provide the necessary service for a reasonable charge, plus shipping and
handling. We require that products accepted for any repair be properly cleaned according to
our recommended care instructions. Please send your product or component that requires re-
pair, postage prepaid, along with a description of what needs attention. For service and repairs,
please contact our Customer Satisfaction Department on 063 872 7667. Warranty Term Limited
two-year warranty applies to all tent components including aluminium base, aluminium extru-
sions, aluminium arms, ladder, canvas and seams.
