Bungard StenPrint 3000 Instruction Manual Download | Manualshive

Page: 30 / 31

background image

31

Instruction manual

© 22.02.2017 Bungard GmbH & Co. KG

6

Technical data

6.1

903.005 - Stencil Printer

Dimensions (W x D x H) ........................................................ 640 x 400 x 150 mm, closed
Base ..................................................................................... 545 x 360 mm
Stencil size ........................................................................... max. 460 x 30 x 350 mm
Table/useable area ................................................................. 390 x 290 mm
Adjustment X/Y ...................................................................... +/- 7,5 mm
Theta-adjustment ................................................................... +/- 3°
Parallel lift ............................................................................. 2 mm
Weight .................................................................................. ca. 15 kg zzgl. Optionen

6.2

903.203 - Stencil holder frame

Dimensions (W x D x H) ......................................................... 500 x 350 x 30 mm
Stencil size max.  .................................................................. 420 x 320 mm
PCB size/useable area max.  .................................................. 380 x 280 mm
Weight ca.  ........................................................................... 1 kg

6.3

903.204 - Stencil clamp frame

Dimensions (W x D x H) ........................................................ 540 x 350 x 40 mm
Stencil size max. ................................................................... 360 x 280 mm
PCB size/useable area max. ................................................... 330 x 270 mm
Weight .................................................................................. ca. 2,3 kg

6.4

903.205 - Stencil clamp for stencils in fixed frames

Dimensions (B x T x H) ..........................................................  350 x 45 x 90 mm
Frame size max.  ...................................................................  350 x 450 x 33 mm
Weight ca.  ...........................................................................  ca. 0,5 kg

6.5

903.103 - Magnetic holders for double-sided printing

PCB underside ...................................................................... max. 18mm

«
...
28
29
30
31
»

Summary of Contents for StenPrint 3000
































Reviews:

No comments

Related manuals for StenPrint 3000

Brand: ABB Pages: 36

Brand: ABB Pages: 40

Brand: Raymarine Pages: 464

Brand: 3M Pages: 8

Brand: ZOLL Pages: 3

Brand: Velocitek Pages: 81

ABS-Lock X-Flat

Brand: ABS Pages: 8

ABS-Lock X-DURCH

Brand: ABS Pages: 8

Brand: ABS Pages: 8

Brand: Keiser Pages: 82

Brand: Keiser Pages: 4

FreeStyle Comfort

Brand: CAIRE Pages: 33

Brand: Garmin Pages: 2

Brand: Landi Renzo Pages: 16

Brand: IBM Pages: 163

Brand: M-Audio Pages: 25

Brand: Pari Pages: 11

Brand: Pari Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands