18
PROGRAMMING CUP SIZES
The cup size can be programmed in portion control models by “EXAMPLE” or “TIME”. Programming by EXAMPLE is
manually pressing desired dispense button, then releasing when the desired cup size is attained. The time required to fill
the cup will be stored in the controller memory by pressing
REDUCED FILL
to save. Programming by TIME is setting the
actual dispense time in seconds for each cup size desired.
Place the “NORMAL/PROGRAM/RINSE” switch in the “PROGRAM” position. Press HOT WATER button until the “SET
CUP SIZE” menu is reached. (Refer to menu N, page 23) Press BOX O JOE button to select programming by “EXAMPLE”.
Place proper cup under dispense tip for station you desire to set. Press desired dispense button, then release when the
cup is 3/4 full. If cup is not full enough, the dispense button can be pressed again to add additional beverage to the cup. If
cup has reached desired level, press REDUCED FILL button under “SAVE” to record the dispense time. If cup is overfilled,
press button D under “REPEAT”. Empty cup and repeat the process.
If setting cup sizes by “TIME” is desired, press button REDUCED FILL under “TIME” in the “SET CUP SIZE” menu.
“HEAD 1 SM TIME” will be displayed, along with current time setting. Pressing either BOX O JOE button below (-) or
REDUCED FILL button below (+) will subtract or add time in .1 second increments, XL and Box-O-Joe in 1.0 second incre-
ments. Each one second of time equals approximately 1.25 ounces of beverage at factory settings. When desired time is
set, press HOT WATER button to continue to next cup size.
When the desired cup sizes have been programmed, press Hidden button to exit program menus, or press button
HOT WATER to move to the next menu. If Hidden button was selected to exit the program mode, return the “NORMAL/
PROGRAM/RINSE” switch to the “NORMAL” position to return to nomal operation.
If recipes have been added to the machine, cup sizes and ratio can also be adjusted by changing the recipe.
Place the “NORMAL/PROGRAM/RINSE” switch in the “PROGRAM” position. Press HOT WATER button until screen:
SET CUP SIZE BY
EXAMPLE TIME
Press Reduced Fill button. Screen will update to:
HEAD #1 RECIPE
RECIPE NAME
Press Reduced Fill button to change recipe. Press Hot Water button to accept change. Press Hot Water button to advance
to other heads if required.
NOTE: If Powder is changed, Powder will need to be re-calibrated.
PROGRAMMING HOT WATER SIZE
Place the “NORMAL/PROGRAM/RINSE” switch in the “PROGRAM” position. Press HOT WATER button until the “SET
CUP SIZE” menu is reached. (Refer to menu D, page 20). Press REDUCED FILL button under “TIME” in the “SET CUP
SIZE” menu. Press foward until “SMALL H/W TIME” and adjust to desired time by pressing BOX O JOE button (-) (page
17) or REDUCED FILL button (+).
Small, Medium, and Large are settable from 1 to 25 seconds in increments on 0.1 seconds, and the Extra Large por-
tion is settable from 1 to 110 seconds in steps of 1.0 seconds. Each one second of time equals approximately 1.0 ounces.
1. ON/OFF/NIGHT switch:
ON: Enables all dispenser functions.
OFF: Disables all dispenser functions.
NIGHT: Night Mode Energy Saver disables display lighting and dispense switches. Tank
temperature drops to 140°F and holds it there.
2. NORMAL/PROGRAM/RINSE switch:
NORMAL: Allows all dispenser functions. Must be in this position for dispensing.
PROGRAM: Allows access to program menus using touch pad and LCD screen.
RINSE: Disables hopper motors. Pressing dispense button on front door will dispense
dilution water and power whipper motor for ten seconds.
2
1
PROGRAMMING THE DISPENSER (cont.)
45398.2 111315
