background image

2

35352 121405

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) All equipment other than as specifi ed below: 2 years parts and 1 year labor.
2) Electronic circuit and/or control boards: parts and labor for 3 years.
3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.
4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: 
parts and labor for 3 years or 30,000 pounds of coffee, whichever comes fi rst.

These warranty periods run from the date of installation. BUNN warrants that the equipment manufactured by 
it will be commercially free of defects in material and workmanship existing at the time of manufacture and 
appearing within the applicable warranty period. This warranty does not apply to any equipment, component or 
part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, 
alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is 
conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone 
at (217) 529-6601 or by writing to Post Offi ce Box 3227, Springfi eld, Illinois 62708-3227; 2) if requested by 
BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior 
authorization from BUNN that the defective equipment is under warranty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR 
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 

The agents, dealers or employees of BUNN 

are not authorized to make modifi cations to this warranty or to make additional warranties that are binding on 
BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and 
should not be relied upon.

If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its 
exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts 
and/or labor (during the applicable parts and labor warranty periods specifi ed above) to repair the defective 
components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace 
the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF 
THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S 
SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profi ts, lost sales, 
loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute 
equipment, facilities or services, or any other special, incidental or consequential damages.

Summary of Contents for Omni




























Reviews: