background image

FACTORY SET VOLTAGE 115 V

TO CHANGE THE VOLTAGE :

Before changing the 

voltage connection:

A) Ensure the power to

the pump is disconnected. 

B) Open motor junction box cover.

C) Please select the up knob

position for 115V or down

knob position for 230V.

D) Connect to appropriate voltage.

E) Close motor junction box.

Your pump has been carefully packaged at the 

factory to prevent damage during shipping. 

However, occasional damage may occur due 

to rough handling. 

Carefully inspect your 

pump

 for damages that could cause failures. 

Report any damage to your carrier or your point 

of purchase.

INSTALLATION

INSTRUCTIONS

JET PUMPS 

MODELS

506121S

(VERSION W 2015)

AND OTHER PRODUCTS

506127S, 506128S

506131S, etc.

Please read these 

instructions

 carefully. 

Failure 

to comply to 

instructions and 

designed

 operation of 

this system,

 may

 void 

the warranty.

© 2018 BURCAM  Printed in Canada 506662

 Discharge  connection

PRIMING PROCESS

Follow all these inside step by step instructions to install your pump. Use teflon tape on 

all threads. (1) Fill the suction line with water and connect it to the suction inlet.  

(2) Remove the priming plug and fill the pump body with water. (3) Screw the plug to the

priming inlet. (4) Turn the power on. The pump should deliver water to the plumbing line

within 30 seconds. If not, unplug the pump and repeat the process at step 2.

2-3

4

Suction connection

1

2190 Dagenais Blvd. West

Laval (Quebec)

Canada

H7L 5X9

Tel. : 514.337.4415

Fax : 514.337.4029

info@burcam.com

see us at

 

www.burcam.com

Summary of Contents for 506121SW











Reviews: