manualshive.com logo in svg

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Introducing the Busch-Jaeger Busch-SmartTouch ST/A10.11-811, a cutting-edge device built to simplify your home automation experience. To unlock the full potential of this exceptional product, a comprehensive Product Manual is available for download - absolutely free! Access the manual today on 88.208.23.73:8080, and discover the endless possibilities that await you.

Share
Download
background image

 

Index

 

 

 

 

 

Product manual 2CKA001473B5342 

│

360

 

Option "Linear measurement display" — Measurement 

display with colour display ....................... 187, 189, 190 

Option "Linear measurement display" — Object type ... 188 

Option "Measurement of power consumption" - Data point 

type .......................................................................... 195 

Option "Measurement of power consumption" - Unit .... 195 

Option "Moisture" — Unit .............................................. 195 

Option "Phase angle" — Unit........................................ 197 
Option "Power factor" — Unit ....................................... 197 

Option "Power" - Data point type .................................. 196 

Option "Power" — Unit ................................................. 196 

Option "Rain" — Text for no rain .................................. 193 
Option "Rain" — Text for rain ....................................... 193 

Option "Status display" — Object type ......................... 183 

Option "Temperature" — Unit ....................................... 193 

Option "Twilight" — Unit ............................................... 194 
Option "Value display" — Measurement display with 

colour display ........................................................... 184 

Option "Value display" — Object type .......................... 185 

Option "Voltage" - Data point type ................................ 195 
Option "Voltage" — Unit ............................................... 195 

Option "Water (volume)" - Data point type .................... 198 

Option "Water (volume)" — Unit ................................... 198 

Option "Wind force" — Unit .......................................... 193 
Option "Wind rose" — Display value in control element190 

Option "Wind rose" — Display value of wind force ....... 191 

Option "Wind rose" — Object type ................................ 191 

Type of display element ................................................ 182 

Type of display element — Option "Brightness" ........... 194 
Type of display element — Option "Round measurement 

display" .................................................................... 189 

Type of display element — Option "Wind rose" ............ 190 

Control element "Fan switch" 

Deactivation of switch-off option ................................... 156 

Display status ............................................................... 158 

Enable 1-bit communication object "Disable" ............... 159 

Icon type ....................................................................... 156 
Name of control element .............................................. 156 

Number of speed levels ................................................ 157 

Object type ................................................................... 157 

Control element "Page link" 

Enable 1-bit communication object "Disable" ............... 209 

Linked with page ........................................................... 208 

Name of control element .............................................. 208 

Control element "RGBW operation" 

Display value in control element ................................... 142 

Enable 1-bit communication object "Disable" ............... 147 

Name of control element .............................................. 142 

Type of colour/white lamp ............................................. 142 

Control element "RGBW operation“ 

Telegram is repeated every [sec.] ................................ 146 

Control element "Rocker switch" 

Enable 1-bit communication object "Disable" ............... 136 
Icon type ....................................................................... 131 

Name of control element .............................................. 131 

Object type ................................................................... 132 

Status control element (icon/text) ... ............................. 132 

Control element "RTC control element" 

Additional functions/objects .......................................... 152 

Changing temperature unit via object ........................... 153 

Delay time ... after reset ................................................152 

Display ..........................................................................153 

Display actual temperature ...........................................153 

Enable 1-bit communication object "Disable" ................154 
Fan coil control during cooling mode ............................154 

Fan coil control during heating mode ............................153 

Fan coil settings cooling ................................................155 

Fan coil settings heating ...............................................155 
Heating/cooling switchover ...........................................153 

Hide temperature unit....................................................153 

Lowest manually adjustable fan speed level .................155 

Master/slave setpoint adjustment via communication 

object........................................................................154 

Master-slave fan speed level ........................................155 

Name of control element ...............................................152 

Number of fan speed levels ..........................................155 
Number of fans..............................................................155 

Step size of manual setpoint adjustment ......................154 

Temperature unit ...........................................................153 

Control element "Scene" 

"Scene number x [1 - 64] ..............................................174 

Enable 1-bit communication object "Disable" ................176 

Long operation after... ...................................................173 

Name of control element ...............................................173 
Name of scene x ...........................................................174 

Number of scenes [1 - 10] .............................................174 

Saving scene x with a long press ..................................175 

Start scene at selection .................................................173 

Control element "Slider" 

Name of control element ...............................139, 161, 167 

Control element "Split Unit Control " 

Use vertical oscillation...................................................164 

Control element "Split Unit Control" 

Additional mode 

Use window contact ................................ 166 

Display actual temperature ...........................................161 

Function icon 125, 131, 137, 139, 142, 148, 152, 156, 161, 

167, 173, 177, 181, 200, 208, 210 

Maximum setpoint .........................................................161 
Minimum setpoint ..........................................................161 

Name of room ......125, 131, 137, 139, 142, 148, 152, 156, 

161, 167, 173, 177, 181, 200, 208, 210 

Number of fan speed levels ..........................................163 
Size of the button ..........................................................210 

Step size of the manual setpoint adjustment ................162 

Use additional mode 

Boost ........................................................ 165 
Forced operation ..................................... 165 
Scene ........................................................  165 

Use additional Presence mode .....................................166 

Use automatic mode .....................................................163 

Use automatic mode for fans ........................................163 
Use cooling mode .........................................................164 

Use drying mode ...........................................................164 

Use extra mode 

Silent mode .............................................. 165 

Use fan mode ................................................................164 

Use horizontal oscillation ..............................................164 

Control element "Switch" 

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

AMX MXT-700 Quick Start Manual preview
MXT-700
Brand: AMX Pages: 2
Acnodes PC 6170 Specifications preview
PC 6170
Brand: Acnodes Pages: 1
InTouch INTS320 User Manual preview
INTS320
Brand: InTouch Pages: 4
Xycom 9465 PC/AT Manual preview
9465 PC/AT
Brand: Xycom Pages: 87
LG 55GA6400 Specification preview
55GA6400
Brand: LG Pages: 2
LG L172WT - - 17" LCD TV User Manual preview
L172WT - - 17" LCD TV
Brand: LG Pages: 38
LG INFINIA 50PK950 Brochure & Specs preview
INFINIA 50PK950
Brand: LG Pages: 2
LG 60PH6700 Service Manual preview
60PH6700
Brand: LG Pages: 64
LG 55GA7900 Quick Setup Manual preview
55GA7900
Brand: LG Pages: 2
LG INFINIA 50PK950 Owner'S Manual preview
INFINIA 50PK950
Brand: LG Pages: 216
LG INFINIA 50PK950 Service Manual preview
INFINIA 50PK950
Brand: LG Pages: 51
LG 60PN5700 Owner'S Manual preview
60PN5700
Brand: LG Pages: 52
LG Flatron W2253TQ User Manual preview
Flatron W2253TQ
Brand: LG Pages: 26
LG LFX25960SB User Manual preview
LFX25960SB
Brand: LG Pages: 40
LG INFINIA 60PK950 Specifications preview
INFINIA 60PK950
Brand: LG Pages: 2
Sony WEGA KLV 21SG2 Specifications preview
WEGA KLV 21SG2
Brand: Sony Pages: 1
Sony WEGA KLV 21SG2 Brochure preview
WEGA KLV 21SG2
Brand: Sony Pages: 2
Sony WEGA KLV S15G10 Operating Instructions Manual preview
WEGA KLV S15G10
Brand: Sony Pages: 60

Brands by name

Popular brands

Load more brands