Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 6 / 364

Table of contents

Product manual 2CKA001473B5342

│

10.7.18

Number of fans ..........................................................................................................................144

10.7.19

Fan speed level data format of master/slave .............................................................................144

10.7.20

Number of fan speed levels .......................................................................................................144

10.7.21

Lowest manually adjustable fan speed level .............................................................................144

10.7.22

Fan coil settings heating ............................................................................................................144

10.7.23

Fan coil settings for cooling .......................................................................................................144

10.8

Control element "Fan switch" ......................................................................................................... 144

10.8.1

Name of the control element .....................................................................................................144

10.8.2

Name of room (otional) ..............................................................................................................145

10.8.3

Size of the button ......................................................................................................................145

10.8.4

Function icon .............................................................................................................................145

10.8.5

Deactivation of switch-off option ................................................................................................145

10.8.6

Icon type....................................................................................................................................145

10.8.7

Number of levels .......................................................................................................................146

10.8.8

Object type ................................................................................................................................146

10.8.9

Display status ............................................................................................................................148

10.8.10

Status control element (icon) is controlled by a separate object ................................................148

10.8.11

Enable 1-bit communication object "Disable" ............................................................................149

10.9

Control "Split Unit Control" ............................................................................................................. 150

10.9.1

Name of the control element .....................................................................................................150

10.9.2

Name of room (otional) ..............................................................................................................150

10.9.3

Size of the button ......................................................................................................................150

10.9.4

Function icon .............................................................................................................................150

10.9.5

Display actual temperature ........................................................................................................150

10.9.6

Minimum setpoint ......................................................................................................................150

10.9.7

Maximum setpoint .....................................................................................................................150

10.9.8

Step size of setpoint adjustment ................................................................................................151

10.9.9

Number of fan speed levels (without AUTO) .............................................................................152

10.9.10

Use automatic mode for fans .....................................................................................................152

10.9.11

Use mode: Automatic ................................................................................................................152

10.9.12

Use mode: Heating....................................................................................................................152

10.9.13

Use mode: Cooling ....................................................................................................................153

10.9.14

Use mode: Drying......................................................................................................................153

10.9.15

Use mode: Fan ..........................................................................................................................153

10.9.16

Use horizontal oscillation ...........................................................................................................153

10.9.17

Use vertical oscillation ...............................................................................................................153

10.9.18

Use extra mode: Silence Mode .................................................................................................154

10.9.19

Use additional mode: Boost ......................................................................................................154

10.9.20

Use additional mode: Forced operation .....................................................................................154

10.9.21

Use additional mode: Scene......................................................................................................154

10.9.22

Additional mode Use window contact ........................................................................................155

10.9.23

Use additional Presence mode ..................................................................................................155

10.9.24

Enable 1-bit communication object "Disable" ............................................................................155

10.10

Control "Split Unit Control" ............................................................................................................. 156

10.10.1

Name of the control element .....................................................................................................156

10.10.2

Name of room (otional) ..............................................................................................................156

10.10.3

Size of the button ......................................................................................................................156

10.10.4

Function icon .............................................................................................................................156

10.10.5

Value [1 byte 0-255] for heating mode.......................................................................................157

10.10.6

Value [1 byte 0-255] for cooling mode .......................................................................................157

10.10.7

Using only fan operation ............................................................................................................157

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands