Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 66 / 364

Commissioning via Busch-free@home®

Product manual 2CKA001473B5342

│

8.3.2 Changing

functions

1. If several panels are available, first select the appropriate panel.
2. Tap on the panel that is to be re-configured.

– If only the position of the function or of the control element is to be changed, then the

function can be shifted onto a free area via drag-and-drop.

3. Tap on the drop-down menu on the right edge of the screen of the respective function to

adjust the function method.

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands