background image

CARRYING THE LOAD

Position  the  bucket  as  low  as  possible  below  the
level  of  the  tractor  hood  for  maximum  stability  and
visibility, whether the bucket is loaded or empty.

Use extreme caution when operating the loader on a
slope  and  keep  the  bucket  as  low  as  possible.  This
keeps  the  bucket  and  tractor  center  of  gravity  low
and will provide maximum tractor stability.

OPERATING  THE  LOADER  ON  A  HILLSIDE
IS  DANGEROUS.  EXTREME  CARE  IS
RECOMMENDED.

DO THIS         NOT THIS

When transporting the load, keep the bucket as low
as possible to avoid tipping, in case a wheel drops in
a rut.

NOT THIS

DO THIS

DUMPING THE BUCKET

Lift  the  bucket  high  enough  to  clear  the  side  of  the
vehicle.  Move  the  tractor  in  as  close  to  the  side  of
the vehicle as possible, then dump the bucket.

LOWERING THE BUCKET

After  the  bucket  is  dumped,  back  away  from  the
vehicle while lowering and rolling back the bucket.

FLOAT POSITION

LOWER

DUMP

RAISE

ROLLBACK

1-LEVER

CONTROL

DUMP

LOWER

FLOAT POSITION

ROLLBACK

RAISE

2-LEVER

CONTROLS

14

CAUTION

Summary of Contents for TOUGH 2347QT
































Reviews: