Bush Hog Utility Vehicle Workshop Workshop Manual Download

Page: 3 / 11

BUSH HOG

UTILITY VEHICLE WORKSHOP MANUAL – SECTION 7: STEERING SYSTEM

TOOLS

SAFETY FIRST

CAUTION

Never work underneath a raised vehicle without adequate support. Use jack stands
to prevent the vehicle from falling. A falling vehicle can cause severe personal
injury or death.

CAUTION

When lifting a vehicle chock the wheels left on the ground to prevent the vehicle
from rolling or sliding backward.

Common hand and shop tools can be used to remove and install
steering system components serviced in the section. All special
tools are listed below.

Ball Joint Removal Tool (1.0-1.5” (25.4-38.1mm):

Needed for

removal of tie rod ends from the strut casting steering arm. Ball joint
removal tools are commercially available in various sizes.

Summary of Contents for Utility Vehicle Workshop












Search results

Summary of Contents for Utility Vehicle Workshop

Reviews:

Related manuals for Utility Vehicle Workshop

Brands by name

Popular brands

Bush Hog Utility Vehicle Workshop, Workshop Manual

Search results

Summary of Contents for Utility Vehicle Workshop

Reviews:

Related manuals for Utility Vehicle Workshop

Brands by name

Popular brands