background image

 
 

DPMS: 

Initial display power management signaling. 
 

Video Off In Suspend: 

This determines the manner in which the monitor is blanked. 
The choice: Yes, No. 
 

Suspend Type: 

Select the Suspend Type. 
The choice: PWRON Suspend, Stop Grant. 

 
MODEM Use IRQ: 

This determines the IRQ in which the MODEM can use. 

The choice: 3, 4, 5, 7, 9, 10, 11 and NA. 
 

Suspend Mode: 

When “Enabled” and after the set time of system inactivity.    All devices 
except the CPU will be shut off. 

The choice: Enabled, Disabled. 
 

HDD Power Down: 

When “Enabled” and after the set time of system inactivity, the hard disk drive 
will be powered down while all other devices remain active. 

The choice: Enabled, Disabled. 

 

Soft-Off by PWR-BTTN: 

Pressing the power button for more than 4 seconds forces the system to 
enter the Soft-Off state when the system has “hung.” 

The choice: Delay 4 Sec, Instant-Off. 

 

Wake-Up by PCI Card: 

An input signal from PME on the PCI card awakens the system from a soft off 
state. 
The choice: Enabled, Disabled. 

 

15” Panel PC User’s Manual 

P7 

 

the inner socket first.    Guiding the hole at each end of the DIMM over the 
retaining post at each end of the DIMM socket. 

 
4.  If you install two DIMMs, install the second DIMM using the same 

procedure as above.   

 
5.  If DIMM does not go in smoothly, do not force it.    Pull it all the way out 

and try again. 

 
6.  Make sure the DIMM is properly installed and locked by the tabs on both 

sides of the socket. 

 

Removing a DIMM: 

To remove the DIMM, use your fingers or a small screwdriver to carefully 
push away the plastic tabs that secure the DIMM at each end.    Lift it out of 
the socket. 
 

Make sure you store the DIMM in an anti-static bag and must be 
populated the same size and manufactory of memory modules. . 

 

2-3  Setting Jumpers and DIP Switches 

There are jumpers and DIP-switches on the system board of the NASA-6822 
Series.    You can set the jumpers to make the necessary operations. 
 
 

 

 
 
 
 
 
 
 

Figure 7:  Jumper Connector 

 
 
For any three-pin jumpers (figure 7), the jumper setting is 1-2 when the 
jumper connects pins 1 and 2.  The setting is 2-3 when pins 2 and 3 are 
connected and so on.  You see a number “ 1 “ and a “ 3 “ printed on the 
circuit board to identify these pins.  And also, there is a second way of 
indication – one of the lines surrounding jumpers is thick, which indicates pin 
NO.1. 

P50 

15” Panel PC User’s Manual

   

 

Summary of Contents for PPC-712T

































Reviews: