background image

Before you start 

This tap is suitable for use at water supply pressures of 

2 bar (min.) to 5 bar (max.). 

This product must be connected to the water supply in 

accordance with the UK Building Regulations. If you are 

in any doubt about these requirements, contact a 

qualified plumber, your local Water Company, or the 

Water Regulations Advisory Scheme (WRAS). 

(a) Identify all components and check pack contents.

(b) Turn off mains water supply. The main stopcock is

usually situated where the supply enters the building

(c) It is also recommended that the hot water heating

system is turned off.

(d) Drain the cold and hot water system. It is

recommended to ensure complete drainage, that all taps

are opened. There is no need to drain the central heating

system.

After Care 

Ensure the tap is fully turned off after use. 

To maintain the appearance of this fitting, ensure it is 

cleaned only using a clean soft damp cloth. A solution of 

warm water and mild liquid detergent may be used where 

necessary and then rinsed thoroughly. Abrasive cleaners 

or acidic cleaners MUST NOT BE USED under any 

circumstances.Avoid contact with solvents. 

Guarantee 

This Premium Drinking Water System is guaranteed to 

be free from faults arising from manufacturing defects for 

a period of 12 months from the date of purchase.

Please retain proof of purchase

Contains parts which if these become loose could be a 

choking hazard to small children. After installation please 

check that the bar levers into the tap head are secure, if 

required please use low strength thread lock to secure 

these parts. 

Please pass these instructions back onto householder for 

retention for future reference. 

NOTE! 

Do not over bend the flexible hoses.

Filter Cartridge

Filter Head

 

7/16 x1/4 

 Push -fit

 

-fit

 

3/8 x1/4 

Push

Braided  Flexible Hose 

1/4" Tubing 

[12] x1

[13] x1

[14] x1

[15] x1

[16] x1

[17] x1

min.

80mm

min.

15mm

max.

3Nm

NOTE!

[01]

 x 1

[06]

 x 1

[02]

 x 1

[04]

 x 1

[03]

 x 1

[05]

 x 1

[07]

 x 1

[08]

 x 

3

[09]

 x 2

[10]

 x 1

[11]

 x 1

Tap Assembly

Bezel 

Spacer

Rubber Clamp

Metal Clamp

Nut

T Piece

Washer

Hoses M/F

Hex Key 

Socket Wrench

Summary of Contents for BWTDWFK-TRIFLO









Reviews: