background image

2019/08 - Indice de révision : D - Code : 29650

TRAITEMENT DE L'EAU

61/72

9. 

WARNING AND ERROR MESSAGES

9.1 

Salt concentration too low or too high

When the salt concentration is within acceptable limits , the salt gauge will rise to a point within the ticked 
( ) zone.

9.1.1  Salt concentration too low

Low salt, the gauge is below the ticked range. The word 'Low' and 

a salt shaker appear:

• 

Fixed if the salt concentration is between 2 and 3 g/litre

• 

Blinking if the salt concentration is bewteen 1 and 2 g/litre

Below a salt concentration of 1 g/litre

the cell will stop producing Chlorine

 and the message 

NO 

CELL

 is displayed at the bottom of the LCD screen LCD.

 

!

IMPORTANT 

A low salt warning could be triggered by excessive build up of scale on the electrodes rather than a 

real  lack of salt. In the event of a low salt warning, check that the electrodes are clean and check the 

salt concentration with a suitable tester in case of doubt.  

A  

faulty temperature sensor

 could also cause a low salt warning

9.1.2  Salt concentration too high

High salt, the gauge is above the ticked range. in addition:

• 

between 5.5 and 6.5 g/litre, the message "High" is displayed.

• 

between 6.5 and 8.0 g/litre, the icon is displayed.

• 

Above 8.0 g/litre, both the message and the icon blink.

At a salt concentration above 10.0 g/litre, the cell stops producing Chlorine and the icon 

   is displayed 

to the right of the LCD screen. The high salt icons blink continuously and the message 

HIGH SALT

 or 

SHRT CELL

 is displayed at the bottom of the screen.

The salt concentration is lowered by renewing a volume of pool water.

If the salt concentration is higher than 6.5 g/l, a volume of the pool water must be renewed 

immediately in order to bring the salt concentration down to an acceptable level.  

Summary of Contents for EES





































Reviews: