background image

OPERATOR NOTICE

OPERATOR MANUAL

10

EPS14P

11

OM-EPS14P2019001-EN

OPERATOR NOTICE

This chapter instructs on safety operation procedures that should followed during the use of 

the BYD forklift.

The operator of the forklift should have obtained the driving permit in accordance with local 

regulations.

Before  operating  the  forklift,  check  the  nameplate  and  capacity  chart  to  know  the  loading 

capacity of the forklift and avoid the overloading during operation.

Warning  signs  and  decals  are  pasted  on  the  forklift.  Get  familiar  with  the  decals  and  its 

contents.

NOTICE

Operator Qualification

Industrial vehicle can only be allowed to be operated by people with the qualification regulated 

by local laws. The operators should be those who have been specially trained and have experience 

in operating the vehicles. The user or other entrusting part must confirm the qualification of the 

operators and make use of the tests before authorizing the person to operate the forklift.

The  operating  company  must  make  sure  that  the  operators  understand  all  the  safety 

messages on the forklifts.

For  the  proprietor,  make  sure  following  safety  instruction  on  your  industrial  vehicles  are 

observed.

Please abide by relevant regulations and guide-principles, such as

(1)  Operation of industrial vehicle

(2)  Lane and operative area regulation

(3)  Diver

s right, responsibility and standard of behavior

(4)  Special operation area

(5)  Daily maintenance and repair

(6)  Regular maintenance and repair

Danger
(1)  Unauthorized persons are not allowed to operate the forklift.

(2)  Safety  devices  and  features  will  provide  extra  safety.  Do  not  deactivate  these  safety 

device and features.

(3)  Make sure that the load is well palletized and trimmed to avoid its protruding the loading 

surface of forklift and thus slipping, collapsing and falling over.

(4)  Any  modification  on  the  forklift  is  not  allowed.  Contact  with  BYD  before  making  any 

modification.

(5)  Do not overload. Before operation, please check the rated loading capacity and loading 

center on the capacity chart. When an attachment has been installed, abide by the rated 

loading capacity given on the attachment.

(6)  Do not operate the forklift after drinking. It might cause severe human injuries.

Summary of Contents for EPS14P







































Reviews: