background image

4

ELECTRICAL

 

!

WARNING

: Compressor installation must be performed by a qualified electrician in accordance with the National 

Electrical Code (NEC) or the Canadian Electrical Code (CEC), the National Electrical Safety Code (NESC) OSHA code, and/or 
any local or state codes having precedence�

Be sure of proper wire sizing and that the circuit breaker and the distance from the breaker is within suggested range� Confirm your 
electrical-supply voltage matches what is required for the motor�

 

!

WARNING

: The compressor must be grounded� Grounding reduces the risk of electric shock� Certain C-Aire Models are 

equipped with a cord that has a grounding wire with a grounding plug� The plug must be plugged into an outlet that is 
installed and grounded in accordance with all local codes and ordinances�

 

!

WARNING

: Improper installation of the grounding plug will result in a risk of electric shock� When repair or replacement of 

the cord or plug is required, do not connect the grounding wire to either flat-blade terminal� The insulated wire with a green 
outer surface and yellow stripes is the grounding wire�

NOTE

: The installation, electric motor, wiring, and all electrical controls must be in accordance with NFPA 70-1996 National Electric 

Code, National Electric Safety Code, and state and local codes� Failure to abide by the national, state, and local codes may result in 
physical harm and/or property damage�

 

!

WARNING: 

These units should not be rewired to change between 115/230v� This is because the solenoid is different and 

will not work properly on the other voltage

 

!

DANGER

: High voltage may cause personal injury or death� Disconnect and lockout/tagout, per OSHA regulation 1910�147, 

all electrical power supplies before opening the electrical enclosure or servicing�

 

!

DANGER

: Never assume a compressor is safe to work on if it is not operating� It could restart at any time� Always 

disconnect/ lockout/tagout before servicing�

 

!

CAUTION

: Dry pipe sprinkler compressor must be wired to a reliable power source to be compliant with AHJ� 

WIRING DIAGRAM

S244/S600/S910 

TERMINAL BOX

SOLENOID

WHITE

BLACK

WHITE

RED

YELLOW

BLACK

RED

BLACK

GREEN

WHITE

BLACK
GREEN

POWER

IN

DIGITAL

AMD

MOTOR

1

5

9

13

2

6

10

14

3

7

11

15

4

8

12

16

 

Summary of Contents for S244B


















Reviews: