background image

C&K Securitech

10

24 HOUR ZONE. 

This zone type is active 24 hours a day irrespective of

whether the control panel is armed or disarmed. In the armed condition it
will signal a full alarm if triggered. In the disarmed condition it will give a
local internal alarm warning only.

FIRE. 

A 24 hour type of zone which will accept connection of 12 volt, 4

wire smoke detectors. Activation will cause a pulsed sounder output to
differentiate from other alarm signals.

PERSONAL ATTACK ZONE. 

A 24 hour type of zone which is to be

connected to personal attack switches. The zone gives full alarm
condition when tripped and an option is available to make it silent.
(remote signalling trigger only).

ISOLATE IN HOME SET. 

An option which can be selected with alarm

type zones. This will make the zone in-operative during the Home set
arming period. Home set arming cannot be selected until one zone has
had this option selected.

ISOLATE IN NIGHT SET. 

 An option which can be selected with alarm

type zones. This will make the zone in-operative during the Night set
arming period. Night set arming cannot be selected until one zone has
had this option selected.

WALK THROUGH ENTRY ROUTE. 

An option which can be selected with

alarm type zones. The zone will act as an extra exit zone, allowing
passage out of the premises. If tripped 

after

 the entry period is started it

will allow walk through to the control or keypad. If tripped before it will act
as a normal alarm zone.

CHIME. 

An alarm zone option which causes the internal sounder to emit a

chime sound if the zone is opened during the disarmed, or day condition.

ISOLATE PERMIT. 

An alarm zone option which allows the user to set the

system and manually isolate this zone. The zone will be disarmed for the
period of one arming only. The next time the panel is set, this zone would
be armed again. Without this option programmed, no manual isolation of
this zone is possible. (See users manual for manual isolate permit usage)

BELLS AND STROBE. 

A 24 hour zone option which, following and alarm

in the day condition, allows full audible and visual warning instead of
internal only.

Summary of Contents for ACTIVE 5
















Reviews: