background image

INETVU® MOBILE SYSTEM QUICK START – HUGHES KA 

 

C-COM Satellite Systems Inc. 

Page 5 

 

 

1.4  Pre-Configuration Check List 

 
The following items should be completed/known prior to configuring the iNetVu® Mobile System. 
Contact the Network Operation Center (NOC) if any of the following items are unknown or if you are 
unfamiliar with them.

 

 

Prior to installing IMS and configuring your system, verify that you are using the minimum requirements 
listed below. C-COM always recommends using the latest version as many fixes and improvements 
have been made. 

 

Note: 

Please contact C-COM if you require more information about modem compatibility as these 

may change without further notice.

 

 

Service Type HNS 

Min. Modem Software 

Min. iNetVu SW/FW 

Interface 

HN 9200 

6.10.0.19+ 

7.7.5+ 

HTTP 

HN 9400 

6.10.0.19+ 

7.7.5+ 

HTTP 

HN 9600 

6.10.0.19+ 

7.7.5+ 

HTTP 

HN 9800 

6.10.0.19+ 

7.7.5+ 

HTTP 

 

  IP Address Satellite Modem  

 

 Satellite 

Coordinate 

 

 DVB 

Parameters 

 

 

  Verify Modem Firmware Version is correct with minimal 6.10.0.19 and that the CFG file has only 

1 LNB setting in the file. The CFG file and or any other changes must be requested and provided 
by the NOC. 
 

Note:

 CFG file must include SWAP command “

InstallationMode=6

” 

this will allow the SWAP 

command to work properly and modem signal will be displayed in iNetVu software. 

 
9200/9400 Series 
The HN9200 is a dual band Ka/Ku/Ex C-band broadband indoor unit. The HN9200 
incorporates advanced modulation to deliver high speed connectivity for bandwidth intensive 
applications at an affordable price. The HN9400 is a new generation dual Ka/Ku/Ex C-band 
satellite router that incorporates advanced LDPC coding allowing for high throughput 
bandwidth. HN9400 supports upstream burst rates of 3.2 Mbps. 
 
9600/9800 Series 
The HN9600 modem is a Ka-band high performance satellite router with a single Intra Facility 
Link (IFL) cable, while the HN9800 is a new generation broadband router designed for high 
throughput satellite applications which incorporate advanced LDPC coding and other 
advanced features. The HN9800 features a single IFL interface link to the outdoor unit 
providing high performance DVBS2 channels.  
 
See Hughes Manuals for more info and modem specifications.     

Summary of Contents for HN 9200




















Reviews: