background image

 

Coastal Amusements Inc.  |  Ring Toss  

8

will continue to light. The data comes through a 9-pin Molex connector that leads from 
the Pi-O board to the 7 rows of bottles. Each row has its own 3-pin connector which 
provides data, +5 volts, and ground (found on the right inside of the rack when being 
viewed from the rear). The data is daisy chained (in each row) from the first bottle to 
the last.  Should a bottle become disconnected, the remainder of bottles down the line 
(in that row) will not light, or not change color.  The order of the rows are counted as 1 
being the closest to the player, and 7 being the furthest away.  

5.

 

Audio/Video; Video comes from the HDMI port on the Raspberry Pi.  The cable (10 foot 
long) from Pi to monitor is male HDMI to male DVI.  Audio comes from the 3.5mm (1/8 
inch) stereo jack on the Pi-I/O board, NOT the Raspberry Pi despite that it has its own 
jack as well. Volume is adjustable from the menu as well as the volume knob on the 
amplifier. Typically, the amplifier is set to some fixed point, and volume is adjusted from 
the menu.  

6.

 

Power; There are two power supplies for the game. A 12 volt 29-ampere supply, and a 5 
volt 100-ampere supply.  Both supplies are UL rated and run on 110v or 220v 50/60 Hz 
mains. However, the operating voltage must be switched manually. The game draws 6.5 
amperes (+ or-) from the mains @110 volts.  The IEC-power 
filter/fuse/switch/connector is rated at 10 amps, 250 volts. 

For the dual-game configuration (2 games side by side) the left-side game (viewed from front) 
has an extra power supply providing 5 and 24 volts for the bonus sign mounted between the 
games. 

 

 

Summary of Contents for RING TOSS















































Reviews: