background image

4

4

Introduction

1.1 

Instructions

Important information and instructions in this documentation are designated as follows:

Danger!

Draws attention to an exceptionally great, imminent danger to your health or life due to hazardous 
voltages.

!

Danger!

Draws attention to a danger with high risk which, if not avoided, may result in death or serious injury.

!

Warning!

Draws attention to a danger with medium risk which, if not avoided, may result in death or serious injury.

!

Caution!

Draws attention to a danger with low risk which, if not avoided, may result in minor or moderate injury.

!

Attention!

Draws attention to potential risks of property damage or loss of quality.

i

Note!

Advice to make work routine easier or on important steps to be carried out.



Environment!

Gives you tips on protecting the environment.

Handling instruction

Reference to section, position, illustration number or document.

Option (accessories, peripheral equipment, special fittings).

Time

Information in the display.

1.2 

Intended Use

• 

The device is manufactured in accordance with the current technological status and the recognized safety rules. 
However, danger to life and limb of the user or third parties and/or damage to the device and other tangible assets 
can arise during use.

• 

The device may only be used for its intended purpose and if it is in perfect working order, and it must be used with 
regard to safety and dangers as stated in the operating manual.

• 

The device applicator mounted on a cab printer of the series is intended exclusively for applying suitable 
materials that have been approved by the manufacturer. Any other use or use going beyond this shall be regarded 
as improper use. The manufacturer/supplier shall not be liable for damage resulting from unauthorized use; the 
user shall bear the risk alone.

• 

Usage for the intended purpose also includes complying with the operating manual, including the manufacturer‘s 

maintenance recommendations and specifications.        

i

Note! 
The complete and current version of the documentation can be found in the Internet.

1.3 

Safety Instructions

!

Attention!

Initiation, adjustments and changing of parts are to be performed by qualified service personnel only.

!

Warning!

This is a class A product. In a domestic environment this product may cause radio interference in which 
case the user may be required to take adequate measures.

Summary of Contents for 5314


















Reviews: