background image

6

cab Produkttechnik GmbH & Co KG

1. Introduction

Introducing the Gemini Windows Barcode Printer

The 

Gemini 

 is an innovative printer designed to work only in a Windows™

environment.  Instead of buttons on a printer's front panel, printer configuration

and control is provided by the Gemini Control Panel Application running under

Windows.  The 

Gemini

  driver  allows printing from almost any Windows

application, such as MS Word™, Write,  WordPad, Access® and Visual

Basic™, as well as Lotus® Approach®, Paradox® and dBASE® among others.

Bar code labels can be created with existing Windows applications using the

special barcode fonts built into the driver, eliminating the need for special

labeling software.

Gemini 

 uses the true type fonts available with your Windows applications, and

accepts all graphic types supported by Windows, resulting in exceptional

flexibility in font and graphic choices.  Fonts and graphics are downloaded as

needed with the high-speed bi-directional Centronics interface, providing an

exceptionally quick time to first label printing.

The 

Gemini

 is built to work only with Windows, and takes full advantage of

Windows features.  Its simple design requires a minimum of effort and

expertise for loading and maintaining the printer.  From configuration and setup

to ongoing operation, use of the online Gemini Control Panel Application

simplifies the operator's job.  Extensive Online Help is provided covering all

features and functions available within the Control Panel Application and

Printer Setup.  In addition, help topics covering 'Printing from Windows

Applications' and 'Barcode and Symbology information' are included.

The Gemini Thermal Transfer Printer is offered in two versions:

Gemini T :

The device is equipped with a tear-off edge to aid the removal of

the labels or continous material by hand after printing.

Gemini TD :

This device has an additional dispensing feature for labels.

Directly after printing the label is removed from the liner and

placed in a dispense position ready for further use. The

presence of a label in the dispense position is regognized by a

sensor which interrupts the printing until the label is removed.

Both versions are available as 230 Volt or 115 Volt devices.

Summary of Contents for Gemini









































Reviews: