background image

Turn  On/Off

  –  To  turn  on  press  the  button  at  the  top  left  of  the 

display. To turn off press and hold this button for 3 seconds. 
 

Charge

 – Connect the supplied power supply. While the camera 

is  charging  the  red  LED  near  the  bottom  right  of  the  case  will 
illuminate. Once fully charged the LED will turn off. 

 
Recording to SD Card

 – Insert an SD card up between 2GB and 

32GB  into  the  underside  of  the  display.  It  is  best  practice  to 
format  an  SD  card  before  use  by  pressing  the  following  buttons: 
<Menu>, <Down>, <Ok>, <Down>, <Down>, <Ok>, <Up>, <Ok>. 
Note that formatting the card will delete all data stored on it. 

 
Record  image  (photo) 

 

Press  <Photo>  from  the  home  screen 

to enter photo mode. The camera icon will be displayed in the top 
left of the screen. To take a photo press the <Shoot> button. To 
exit photo mode press the <Exit> button. 

 

 
Record  video 

 

Press  <Video>  from  the  home  screen  to  enter 

video mode. The video icon will be displayed in the top left of the 
screen. To begin recording press <Rec>, to stop press <Stop>.

 

Summary of Contents for FERRET CF2810C

















Reviews: