background image

 

Chapter 1: 

 

Introduction

 

1-6

FOMIM User’s Guide

 

Error (ERR) LED

 

When lit, this red LED indicates the temperature within the MMAC 
chassis has risen to 40

 

°

 

C or greater. The FOMIM alerts the management 

board, and the FOMIM in turn receives a signal to light the LED.

 

1.5

RELATED MANUALS

 

The manuals listed below should be used to supplement the procedures 
and other technical data provided in this manual. The procedures 
contained in these manuals will be referenced, rather than repeated, in this 
manual.

Cabletron Systems 

 

Multi Media Access Center (MMAC-M3FNB, 

MMAC-M5FNB, and MMAC-M8FNB) Overview and Set Up Guides

 

.

Cabletron Systems 

 

FOT-F3 Fiber Optic Transceiver User's Manual.

 

1.6

GETTING HELP

 

If you need additional support related to this device, or if you have any 
questions, comments, or suggestions concerning this manual, contact 
Cabletron Systems Technical Support:

By phone

(603) 332-9400
Monday – Friday; 8 

 

A

 

.

 

M

 

. – 8 

 

P

 

.

 

M

 

. Eastern Time

By CompuServe

GO CTRON from any ! prompt

By Internet mail

support@ctron.com

By FTP

ctron.com (134.141.197.25)

Login 

 

anonymous

 

Password 

 

your email address

 

Before calling Cabletron Systems Technical Support, have the following 
information ready:

A description of the failure

A description of any action(s) already taken to resolve the problem 
(e.g., changing mode switches, rebooting the unit, etc.)

A description of your network environment (layout, cable type, etc.)

Network load and frame size at the time of trouble (if known)

Summary of Contents for 38


































Reviews: