Cabletron Systems 9F426-03 Appendix Download | Manualshive

Page: 12 / 14

background image

9F426-03 Module Specific Information

10

Full Duplex Configuration Screen

The Full Duplex Configuration Screen (Figure 4), allows you to specify transmit
and receive settings for the module’s front panel ports.

Figure 4. Full Duplex Configuration Screen

SmartSwitch 9000 Local Management

Full Duplex Configuration

Module Name: 9F426-03 Firmware Revision: 01.04.10

Slot Number: 9 BOOTPROM Revision: 01.02.00

PORT# OPERATION MODE LINK STATUS PORT STATUS

1 FULL DUPLEX No Link ENABLED

2 FULL DUPLEX No Link ENABLED

3 FULL DUPLEX No Link ENABLED

SAVE SET ALL PORTS: FULL EXIT RETURN

«
...
10
11
12
13
14
»

Summary of Contents for 9F426-03















Reviews:

No comments

Related manuals for 9F426-03

Brand: B&B Electronics Pages: 26

Brand: B&B Electronics Pages: 15

Brand: B&B Electronics Pages: 45

Brand: Daxten Pages: 2

Brand: Hama Pages: 10

Brand: Hama Pages: 14

S5560S-EI Series

Brand: H3C Pages: 37

OfficeConnect WX4400

Brand: 3Com Pages: 528

Brand: Gefen Pages: 31

Brand: ORiNG Pages: 2

TIMEGUARD WF10COM

Brand: Theben Pages: 35

OmniView Secure F1DN102Uea

Brand: Belkin Pages: 36

Brand: Silent Gliss Pages: 4

Brand: Atlantis Land Pages: 3

Brand: Key Digital Pages: 20

Brand: Nextech Pages: 4

3CB9E7 - CoreBuilder 9000 Chassis Switch

Brand: 3Com Pages: 132

Brand: Intellinet Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands