manualshive.com logo in svg

Cabletron Systems SSR-GLX19-02, User Manual


Share
Download
background image

CoreWatch User’s Manual

141

Chapter 9: Configuring Unicast Routing on the SSR

Note:

The metric 16 (the default) is equivalent in RIP to “infinite” and makes a route 
unreachable. You must set the default metric to a value other than 16 in order 
to allow the SSR to export routes from other protocols such as OSPF into RIP.

You can specify values for the default route preference and default metric in 
the 

RIP Global Parameters

 dialog box just as in the 

RIP Policy Defaults

 

dialog box. If you change a parameter in one dialog box, that change is 
automatically applied to the other dialog box. See 

“Setting RIP Routing Policy 

Defaults” on page 298

 for more information.

8.

Specify whether the SSR broadcasts RIP packets regardless of the number of interfaces 
present by doing one of the following:

–

Select 

On

 to configure the SSR to always send RIP broadcasts regardless of the 

number of interfaces present.

–

Select 

Off

 to configure the SSR to never send RIP broadcasts on attached interfaces.

–

Select 

Choose

 to configure the SSR to send RIP broadcasts only if more than one 

interface is configured on the SSR. This is the default state.

9.

Click 

OK

.

Defining IP RIP Interfaces

By default, RIP is disabled on all SSR IP interfaces. To enable RIP on an IP interface, you 
define an IP RIP interface to set the following parameters on that interface:

–

Whether the interface will accept RIP updates

–

Whether the interface will send RIP updates

–

The RIP version (1 or 2)

–

The packet type used for RIP updates (broadcast or multicast)

–

The metric added to incoming RIP updates

–

The metric added to outgoing RIP updates

To enable RIP on an IP interface or to modify the settings of an existing IP RIP interface:

1.

Start Configuration Expert if you have not already done so. 

2.

Open the configuration file you want to modify and then double-click that file’s 
Routing Configuration object.

3.

Double-click the IP Routing Configuration object.

4.

Double-click the IP Unicast Routing object and then double-click the RIP Routing 
object. Double-click the RIP Enabled Interfaces object. 

5.

Do one of the following:

Summary of Contents for SSR-GLX19-02
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SSR-GLX19-02

AMX RMS Administrator'S Manual preview
RMS
Brand: AMX Pages: 212
ACRONIS DISK DIRECTOR SUITE 10 User Manual preview
DISK DIRECTOR SUITE 10
Brand: ACRONIS Pages: 127
Lenovo ThinkCentre A58 Specifications preview
ThinkCentre A58
Brand: Lenovo Pages: 2
DeLorme Topo North America User Manual preview
Topo North America
Brand: DeLorme Pages: 369
Meade Autostar II Instruction Manual preview
Autostar II
Brand: Meade Pages: 62
Nikon 25385 - Capture NX - Mac User Manual preview
25385 - Capture NX - Mac
Brand: Nikon Pages: 268
GRASS VALLEY AURORA EDIT - INSTALLATION V7.1 Installation Manual preview
AURORA EDIT - INSTALLATION V7.1
Brand: GRASS VALLEY Pages: 152
MINOLTA-QMS Crown Document Option Commands Reference Manual preview
Crown Document Option Commands
Brand: MINOLTA-QMS Pages: 134
Autodesk 24108-051462-9000 - AUTOCAD REVIT ARCH STE 08 COMM NEW SLM DVD Questions And Answers preview
24108-051462-9000 - AUTOCAD REVIT ARCH STE 08 COMM NEW SLM DVD
Brand: Autodesk Pages: 11
Autodesk 057A1-05A111-10MD - AutoCAD LT 2009 Manual preview
057A1-05A111-10MD - AutoCAD LT 2009
Brand: Autodesk Pages: 31
Autodesk 12909-091452-9750 - Map 3D 2006 Student Edition Installation Manual preview
12909-091452-9750 - Map 3D 2006 Student Edition
Brand: Autodesk Pages: 35
Autodesk 057A1-05A111-10MB - AutoCAD LT 2009 Installation Manual preview
057A1-05A111-10MB - AutoCAD LT 2009
Brand: Autodesk Pages: 58
Autodesk 15606-011408-9330 - MAPGUIDE R6.3 SITE LIC-UPG R6 Developer'S Manual preview
15606-011408-9330 - MAPGUIDE R6.3 SITE LIC-UPG R6
Brand: Autodesk Pages: 94
MACROMEDIA DIRECTOR MX 2004-DIRECTOR SCRIPTING Reference preview
DIRECTOR MX 2004-DIRECTOR SCRIPTING
Brand: MACROMEDIA Pages: 1130
IBM ZVM - FOR LINUX V6 RELEASE 1 Getting Started preview
ZVM - FOR LINUX V6 RELEASE 1
Brand: IBM Pages: 172
FARONICS CORE - MIGRATION GUIDE 11-2009 Manual preview
CORE - MIGRATION GUIDE 11-2009
Brand: FARONICS Pages: 32
NEC KT-X46UN User Manual preview
KT-X46UN
Brand: NEC Pages: 57
Commax CCU-310EV Product User Manual preview
CCU-310EV
Brand: Commax Pages: 34

Brands by name

Popular brands

Load more brands