manualshive.com logo in svg

Cabletron Systems SSR-GLX19-02, User Manual


Share
Download
background image

Chapter 12: Configuring QoS on the SSR

204

CoreWatch User’s Manual

–

To delete interfaces, select them in the 

Selected Interfaces

 list and click the 

Delete

 

button.

7.

Click 

OK

.

Dragging an Interface to Apply a Flow to the Interface

You can add an interface to a QoS profile’s list of interfaces by dragging the interface to 
the flow. This will apply the flow to the interface. To apply a flow by dragging an interface 
to a QoS profile flow:

1.

Start Configuration Expert if you have not already done so. 

2.

Open the configuration file you want to modify and double-click that file’s QoS 
Configuration object. Then do one of the following:

–

If you want to apply a flow to an IP interface, double-click the IP QoS Profiles 
object.

–

If you want to apply a flow to an IPX interface, double-click the IPX QoS Profiles 
object.

3.

Double-click the Routing Configuration object. Then do one of the following:

–

If you are applying an IP flow to an IP interface, double-click the IP Routing 
Configuration object. Then double-click the IP Interface Configuration object.

–

If you are applying an IPX flow to an IPX interface, double-click the IPX Routing 
Configuration object. Then double-click the IPX Interface Configuration object.

4.

Double-click the object in which the desired interface is located.

If you are applying the flow to an IP interface, the interface is located in either the IP 
interfaces bound to Ports or IP interfaces bound to VLAN object.

If you are applying the flow to an IPX interface, the interface is located in either the IPX 
interfaces bound to Ports or IPX interfaces bound to VLAN object.

5.

From the list of interfaces that appears, select the one you want to add to the flow. 

6.

Drag the selected interface to the desired QoS profile flow

Changing a Layer-2 Port List

If you want to change which ports an existing Layer-2 flow applies to, modify the flow’s 
list of ports. To do so, take the following steps:

1.

Start Configuration Expert if you have not already done so. 

2.

Open the configuration file you want to modify and then double-click that file’s QoS 
Configuration object.

3.

Double-click the Layer-2 QoS Profiles object.

Summary of Contents for SSR-GLX19-02
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SSR-GLX19-02

Novell ZENworks 7.2 Linux Management Manual preview
ZENworks 7.2 Linux Management
Brand: Novell Pages: 10
Tascam GigaStudio 3.04 Supplement Sheet preview
GigaStudio 3.04
Brand: Tascam Pages: 2
MACROMEDIA FLEX Reference preview
FLEX
Brand: MACROMEDIA Pages: 830
Yamaha DM2000 V2.1 Supplementary Manual preview
DM2000 V2.1
Brand: Yamaha Pages: 4
Yamaha ASIO DirectKS Owner'S Manual preview
ASIO DirectKS
Brand: Yamaha Pages: 6
Yamaha Audio Owner'S Manual preview
Audio
Brand: Yamaha Pages: 7
Yamaha Arp Owner'S Manual preview
Arp
Brand: Yamaha Pages: 9
Yamaha AE041 Owner'S Manual preview
AE041
Brand: Yamaha Pages: 11
Yamaha Card Filer Manual preview
Card Filer
Brand: Yamaha Pages: 15
Yamaha Add-On Effects Manual preview
Add-On Effects
Brand: Yamaha Pages: 14
Yamaha AN200 Editor Manual preview
AN200 Editor
Brand: Yamaha Pages: 72
Yamaha 03DVEK Owner'S Manual preview
03DVEK
Brand: Yamaha Pages: 129
DeLorme Street Atlas USA 2011 User Manual preview
Street Atlas USA 2011
Brand: DeLorme Pages: 265
2Wire Wireless PCI Adapter Driver Installation Instructions preview
Wireless PCI Adapter Driver
Brand: 2Wire Pages: 4
Pfaff CREATIVE 4D Brochure preview
CREATIVE 4D
Brand: Pfaff Pages: 8
VERITAS GFN 13820 User Manual preview
GFN 13820
Brand: VERITAS Pages: 580
Pantone Goe System User Manual preview
Goe System
Brand: Pantone Pages: 12
Genius NAVIGATOR 380 - Quick Start Manual preview
NAVIGATOR 380 -
Brand: Genius Pages: 26

Brands by name

Popular brands

Load more brands