Cabletron Systems SSR-GLX19-02 User Manual Download

Page: 316 / 495

Chapter 16: Configuring Routing Policies on the SSR

316

CoreWatch User’s Manual

Specify the origin for your AS export source by selecting the appropriate type
from the

Origin

drop-down list. You can select one of the following four options:

–

any

–

igp

–

egp

–

incomplete

11. Specify whether the SSR restricts the AS path export or associates a metric with the

exported route by doing one of the following:

–

If you do not want the SSR to export any routes from the source, select the

Restrict

export to the specified AS Path source

option.

–

If you want the SSR to associate a metric with the exported route, select a metric
from the

Route Metric

drop-down list. Select

Inherited

if you want the route to use

the policy’s default metric. Otherwise, select a number from 1 to 16.

12. Click

13. Repeat

step 9

through

step 12

until you create all of the AS Path export sources you

plan to include in your export policies.

Configuring and Modifying Tag Export Sources

A tag export source building block specifies a source for exporting routes associated with
a particular tag type into other protocols.

To define tag export source building blocks:

Start Configuration Expert if you have not already done so.

Open the configuration file you want to modify and then double-click that file’s
Routing Configuration object.

Double-click the IP Routing Configuration object.

Double-click the IP Unicast Routing object.

Double-click the Routing Policy Configuration object.

Double-click the Building Blocks object.

Double-click the Export Source object.

Double-click the Tag object, and then do one of the following:

–

If you are creating a new export source, click the Configure New Tag Export Source
object.

–

If you are modifying an existing export source, select that export source.

Summary of Contents for SSR-GLX19-02
















































































































































































































































































































































































































































































































Search results

Summary of Contents for SSR-GLX19-02

Reviews:

Related manuals for SSR-GLX19-02

Brands by name

Popular brands

Cabletron Systems SSR-GLX19-02, User Manual

Search results

Summary of Contents for SSR-GLX19-02

Reviews:

Related manuals for SSR-GLX19-02

Brands by name

Popular brands