A Division of CTI Audio, Inc. * 341 Harbor St. * Conneaut, OH 44030 * (440) 593-1111 * Fax (440) 593-5395
60%
Figure 6
Figure 5
Figure 4
POSITION
METAL CLIP UNDER
RING HERE
Re-stringing the elastic cords.
Follow the instructions below if the elastic cords are removed and need
to be remounted:
For the large circular ring use the elastic cord that is formed in a loop.
1) Using the diagram in
Figure 4
, start by placing the cord in slot #1.
Position the metal clip on the underside of the ring at this position.
2) Using a "wrapping" motion, stretch the cord and use the number guide
to install the cord.
3) When complete, the elastic should look like the diagram in
Figure 5
.
4) Adjust the elastic so that there is nearly equal tension on the individual
segments.
For the smaller "C" shaped ring use the short elastic cord that has a small
loop at each end.
1) Look at the diagram in
Figure 6
and attach the elastic cord as shown
2) When complete the prongs of the triangular bracket should point
towards the large ring.
ZM-1G Equitek shock mount
Mounting a microphone in the ZM-1G
Unscrew the small knurled adapter and rubber ring from the large knurled
knob as shown in
Figure 1
. Screw the adapter and ring snugly into the
bottom of the microphone as shown in
Figure 2
. Slide the microphone
into the mount and screw the knurled knob back into the adapter as
shown in
Figure 3
. Make certain that the microphone is positioned as
shown with the microphone connector centered in the opening of the
metal ring. An XLR connector that is inserted into the microphone will
not touch the metal frame of the
ZM-1G
if the microphone is positioned
properly. The elastic cords in the larger ring should be positioned so that
they fall in the name band area in the middle of the microphone.
Figure 1
Figure 2
Figure 3
TWO-YEAR LIMITED WARRANTY
CTI Audio, Inc. (CAD) hereby warrants that this product will be free of defects in material and workmanship for a
period of two years from the date of purchase. In the unlikely event a defect occurs CAD will, at its option, either repair or replace with
a new unit of equal or greater value. You should retain proof of purchase to validate the purchase date and return it with any warranty
claim. Return warranty claims carefully packed, insured and prepaid to the Service Department at the address listed below.
This warranty excludes exterior finish or appearance, damage from abuse, misuse of the product, use contrary to CADs
instructions or unauthorized repair. All implied warranties or merchantability or fitness for a particular purpose are hereby disclaimed
and CAD hereby disclaims liability for incidental, special or consequential damages resulting from the use or unavailability of this
product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some
states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty
lasts, so the above exclusions and limitations may not apply to you.
Note: No other warranty, written or oral is authorized by CTI Audio, Inc.
A Special Note About Batteries
The high quality rechargeable batteries used in the Equitek
E-350
may either
be Nickel Cadmium or Nickel Metal Hydride. They were selected to provide
long life with virtually no maintenance and have a number of properties that
make them superior to most commonly available rechargeable "9 volt"
batteries:
1) Higher output voltage
2) Lower self discharge rate
3) High immunity to overcharging
If the
E-350
is operated with a 48 volt phantom power supply it is unlikely
they will ever need to be recharged, even if the microphone is unused for
months. If it should ever become necessary to replace the batteries or if you
simply want a spare set, we suggest that you buy replacements from us.
This is not because we are trying to sell batteries, but because we want you
to continue to realize the maximum performance capability of your Equitek
microphone. Contact the
CAD
sales department to purchase replacement or
additional batteries.
Cardioid
Figure 8
Omnidirectional
Equitek E-350 Frequency and Polar Response
Description
The
CAD
ZM-1G
is a full elastic suspension system for shock isolating
all
CAD
Equitek cylindrical multi-pattern microphones. The
ZM-1G
eliminates mechanical shock interference that is transmitted through the
microphone stand by footsteps, machinery, or other vibration sources.
The
ZM-1G
also incorporates a built in swivel for ease of microphone
positioning. The
ZM-1G
attaches to microphone stands with a standard
5/8" x 27 thread.
All manuals and user guides at all-guides.com
