APP-VI
J-Type
Revision J2005-2
buffer for the MIDI Port is already full, the data cannot be queued and is therefore
lost. This error sometimes occurs when scanning through a list of Cues very quickly.
0,',
#
LQ
#
RYHUIORZ
New MIDI messages are being received quicker than the CCM can handle them as
the queue is full. The message will be lost.
0,',
#
,54
#
2YHUUXQ
0,',
#
,54
#
3DULW\
0,',
#
,54
#
)UDPLQJ
An error receiving MIDI data at the interrupt level. This is the lowest of data handling
and is probably indicative of cabling problems or electrical interference.
%DG
#
0,',
#
SRUW
New MIDI data has been received from the automation system but MIDI port speci-
fied is not recognized. This error would perhaps be indicative of poor quality commu-
nications cables or electrical interference.
0,',
#
EXIIHU
#
HU;
A number of errors with the MIDI buffers are reported as follows:
0,',
#
EXIIHU
#
HUU
4
Incorrect Type byte in MIDI Block Message
0,',
#
EXIIHU
#
HUU
5
Unrecognized destination in MIDI Block Message
0,',6HT
#
2YHUIORZ
The input buffer has been completely filled while recording a MIDI sequence. The
recording must stop.
The following message can occur when using the older serial RS232 communica-
tions:
7;
#
%XII
#
2YHUIORZ
%DG
#
/RFDO
#
5HVHQG
1R
#
UHSO\
#
IURP
#
3&
7;
#
%XIIHU
#
)XOO
%UHDN
#
UHFHLYHG
5;
#
%XII
#
2YHUIORZ
5;
#
%ORFN
#
WRR
#
ELJ
'HOD\
#
GXULQJ
#
5;
%DG
#
&6XP
#
LQ
#
5;
%DG
#
3&
#
+HDGHU
#
%DG
#
3&
#
&RPPV
This is not actually an error but it is used to report the status of the Fast Copper
Comms. The Comms warning LED is lit and the ERR button flashes when the CCM
is not communicating with an automaton system.
-
%DG
#
&38
#
FORFN
-
This error may occur if the micro-processor crystal clock is not a recognized fre-
quency i.e. not 11.0592MHz or 16MHz.
%DG
#
&RPPV
#
6WDWXV
A status has been received from the “motor fader communications processor” that
does not match any of the known status reports.
+RVW
#
EXIIHU
#
HUU;
This error is reported when the CCM tries to pass a command to the “motor fader
communications processor” and experiences a problem. The following error codes
are defined:
X=0 Command Queue is full
8VHU
#
$FWLRQV
Sometimes you may log a particular action requested by the user (or performed by
Summary of Contents for J-Type
