J-Type CCM
2-11
Revision J2005-2
J-Type
“root” displays, (see above for descriptions of the root displays). You can always get
back to the root display by pressing the [Esc] key one or two times.
■
■
■
■
Press the [Mem] key.
■
■
■
■
Enter the number of the internal memory required.
■
■
■
■
Press the [Rcl] key.
The current console state is replaced by the state stored in the internal memory.
519
7KH
#
6\VWHP
#
6HWXS
#
PHQX
This is a set of menus which are navigated by using the up and down arrow keys [
↑
]
and [
↓
], with selections being made by pressing enter [
↵
], and cancelled by pressing
[Esc].
Menu items appear in the display with either a question mark (?) or pair of
arrows(
⇑⇓
) on the right. The arrows indicate that this is the title of the current menu
and that the user should press the up and down arrow keys to make a selection. The
question mark means that this is a selectable item, (press [
↵
] to select). The menu
wraps around, so if you move down from “User setup?” you get to “System setup
⇑⇓
“again. In order to speed up the action of traversing these menus, they
do not
reset themselves to the title position each time that they are used. For example; if
“Map Faders?” was selected the last time the [Sys] key was pressed, then the “Map
Faders?” option will appear again, the next time the [Sys] is pressed (provided that
the CCM has not been reset).
Press the [Sys] key.
The first menu contains the following items:
#
System setup
⇑⇓
Title
Map Faders
?
Perform fader mapping.
Map Routers
?
Perform router mapping.
Map Chans
?
Perform mapping of programmable channels
Map Groups
?
Perform programmable group mapping.
Map Aux Groups
?
Perform mapping of programmable Aux groups
Test System
?
Move to the system test menu
User setup
?
Move to the user setup menu
The Map Faders, Router and Groups options will immediately perform that operation,
whereas the Test System and User Setup selections lead on to other menus:
System Test
⇑⇓
Title
Test Faders1
?
Test routines for channel and group faders
Test Faders2
?
Read information from the motor faders
Test Motor VCRs
?
Check mechanical operation of motor faders
Test Keys
?
Check keys indicate on the display
Test MIDI
?
Send programme changes to MIDI-connections
Test Events
?
Check relays and indication of events
Test Comms
?
Check communications busses
Test Routers
?
Check routers
Test Pot Nulls
?
Check if the pot nulls out in the centre position
Test Modul Bus
?
CADAC TESTS
Show Time
?
Show real-time clock
Show Date
?
Show real-time clock and date
View Error Log
?
Look through the last recorded errors
Clear Error Log
?
Clear the error log.
.
.. and...
User Setup
⇑⇓
Title
Enable options
?
Set 2nd Function on or off
Set P&N Keys
?
Select how the P and N buttons are illuminated.
Midi PC Filter
?
Program change filter on/off
MIDI All off
?
All notes off messages on/off
Show Map Addresses ?
Shows Module/Fader addr.while mapping on/off
GroupLnk
?
Configure channel faders relative to master
Summary of Contents for J-Type
