J-Type CCM
2-13
Revision J2005-2
J-Type
Continue until all the routers have been mapped. The display in the CCM will show
the total number of routers mapped.
If you are satisfied that the routers have been mapped correctly, press to [
↵
] stop
mapping and store the new map, otherwise press [Esc] to cancel this operation.
51916
&KDQQHO
#
0DSSLQJ
Channel mapping allows mapping of the actual programmable channels:
STEREO INPUT
DUAL INPUT
DUAL INPUT WITH SUBGROUP ROUTING
■
■
■
■
Select “Map Chans” from the system menu and press [
↵
].
The CCM display changes to “Chans: 0”
■
■
■
■
Map individual channels by pressing the MUTE-button (red button with an M) of
the channel on the console.
■
■
■
■
When required channels have been selected, press [
↵
].
The display changes to “Save New Map?”
If you want to save the map, press [
↵
] or [Esc] to cancel the operation.
51917
3URJUDPPDEOH
#
*URXS
#
0DSSLQJ
The following instructions only apply to 7170-1 and 7925 Group modules.
Mapping does
not affect the audio bus connections of the module, which are set
internally.
■
■
■
■
Ensure all programmable groups are NOT ISOLATED.
■
■
■
■
Select “Map Groups?” from the system menu and press [
↵
].
■
■
■
■
CCM display changes to “Groups: 0”.
■
■
■
■
Press the SUB-GROUP MUTE button of the group module that you wish to be
“group 1".
The MUTE led will illuminate briefly then extinguish - the CCM display should now
read “Groups: 1". Continue until all the groups have been mapped. The display in the
CCM will show the total number of groups mapped.
If you are satisfied that the groups have been mapped correctly, press [
↵
] to stop
mapping and store the new map, otherwise press [Esc] to cancel this operation.
51918
$X[LOLDU\
#
*URXS
#
0DSSLQJ
Each console can have up to 3 auxiliary programmable group modules. The physical
address of each of these is preset at factory, so that when a group is selected by
pressing the Aux Group MUTE-button, the address is automatically given.
Mapping does
not affect the audio bus connections of the module, which are set
internally.
■
■
■
■
Ensure all programmable Aux Group modules are NOT ISOLATED.
■
■
■
■
Select “Map Aux Group?” from the system menu and press [
↵
↵↵
↵
].
■
■
■
■
Press the Aux Group MUTE button of the module that you wish to be “module 1".
The MUTE led will illuminate briefly then extinguish - the CCM display should now
read “Aux Groups: 0“. Continue until all the groups have been mapped. The display
in the CCM will show the total number of Aux Group modules mapped (max 3).
Summary of Contents for J-Type
