J-Type CCM
2-21
Revision J2005-2
J-Type
*URXS
0
/LQN
#
RQ
In Group-Link mode, the DC master faders can “move” channel faders. AUX from
VCA does not have the same meaning as in a non-motor fader system.
When AUX VCA is not selected on a channel fader:
■
■
■
■
The channel fader MUTE button only effects the
main audio output from a chan-
nel
■
■
■
■
When the AUX VCA switch is selected on a fader:
■
■
■
■
The channel fader MUTE button affects the main and the post fader aux. send
signals from the channel.
Channel faders selected to a DC master fader will always “follow” the DC master
Fader. Channel and DC master faders may be programmed for “Snapshot” position
changes and can be used in dynamic cues.
0RWRU
#
IDGHU
#
EHKDYLRXU
#
ZKHQ
#
VZLWFKLQJ
#
EHWZHHQ
#
PRGHV
When entering or leaving
Group-Link mode, the channel fader position will change if
it is assigned to a VCA group other than 0, and the relevant DC master is set at a
position other than 0dB
51915:
7ZLQ
#
PDVWHUV
This option is used in the event that an external master fader box is connected to the
console. When “twins” are enabled, moving a Master Fader will cause its twin to
move in the same way. This allows a modicum of remote control.
■
■
■
■
Using the arrow keys, select
“Twin masters” in the menu “User Setup” and press
[
↵
].
■
■
■
■
Select the number tax of Twin masters in the box, by pressing [
↵
] until the
number appears on the CCM display.
Press [Esc] to go back to the
“User Setup” menu.
51915;
(YHQW
#
GXUDWLRQ
The Events-function allows control of external equipment, such as CD-players, tape-
decks, effects-boxes etc. via 8 relays within the CCM. These relays can be in one of
three states:
ON = always on
OFF = always off
PULSE = toggles between on and off
PULSE duration can be set to a value (1-25) as required to control the external
equipment.
■
■
■
■
Using the arrow keys elect
“Event Duration” in the menu “User Setup” and press
[
↵
].
■
■
■
■
The display shows “Event Dur: “
■
■
■
■
Press [
↵
] again until PULSE is set to a value between 1-25 (25 = 3 sec).
Press [Esc] to go back to the
“User Setup” menu.
Summary of Contents for J-Type
