General Precautions
v
J-Type
Revision J2005-2
*HQHUDO
#
3UHFDXWLRQV
'DPDJH
Do not place heavy objects on the control surface, expose it to sharp objects or han-
dle the console in any way that may cause damage e.g. rough handling and/or
excessive vibration.
(QYLURQPHQW
Do not subject the equipment to dirt, dust, heat or vibration during operation or stor-
age. Never expose the console to rain or moisture in any form. Should the console
become wet, turn it off and disconnect from mains without further delay. The console
should be given sufficient time to dry out, before recommencing operation.
&OHDQLQJ
When cleaning the console, never use chemicals, abrasive substances or solvents.
The console control panels should be cleaned using a soft brush and a dry lint-free
cloth. For persistent marks, use a soft cloth and isopropyl alcohol. Switches and
potentiometers do NOT require cleaning or lubrication. For faders, see below.
7UDQVSRUW
Transport the console in its purpose built flight-case; whilst at the same time taking
precautions to protect the control surface from any damage. Always make sure ade-
quate manpower is available and correct lifting methods are taken when moving the
console.
6DIHW\
#
,QVWUXFWLRQV
Read the following before using the equipment:
,QVWUXFWLRQV
Keep these instructions for future reference. Follow all warnings in this manual and
those printed on the power supply units.
,QVWDOODWLRQ
The console must be installed following the guide lines in this manual. Never connect
power amplifier outputs directly to the console. Connectors and plugs must never be
used for any other purpose than for what they are intended.
&RYHUV
Never use the power supply units without covers fitted. All service work must be car-
ried out by qualified personnel only.
3RZHU
The power supply units must always be connected to correctly rated mains power as
referred to in this manual and marked on the power supply units. The power supply
units must, at all times, be connected to the local mains power supply using the sup-
plied power cord. In cases where the supplied plug does not fit, a qualified electrician
must be consulted.
3RZHU
#
FRUG
The power cord must be routed in such a way that the risks of accidentally stepping
on it, stretching it or it being pinched, are minimized.
:DUQLQJ
THIS EQUIPMENT MUST BE EARTHED !
0RLVWXUH
In order to minimize risks of fire hazards and/or electric shock, the power supply unit
must never be exposed to moisture or water in any form; or be used in a damp or wet
environment. Never place liquid containers, such as for instance coffee/tea mugs, on
the power supply unit, so as to avoid spillage into openings.
9HQWLODWLRQ
Ventilation slots on the power supply or the console must never be covered or in any
other way obstructed. Air flow required for safe operation may otherwise be
restricted. Where the console is to be operated in its flight-case, then this must be
located in such a way that it allows for proper ventilation.
6HUYLFH
Refer servicing to qualified technical personnel only.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Summary of Contents for J-Type
