background image

24

DISPLAY

DESCRIPTION

End Dnld

End Download

Download session is ended.

Cancel

Cancel

System is disarmed and the Cancel button was
pressed within 5 minutes of an alarm.

Gnd Flt

Ground Fault

A short to ground has been detected.

Man Test

Manual Test

Bell and/or communicator test while system is in
disarmed condition.

Re-exit

Re-Exit

The exit delay has been re-started without
disarming the system.

Output Trip

Output Trip

A trip has occurred on an expander auxiliary
output.

Data Lost

Data Lost

Communication of a signal has failed (log only
event).

Walk-test

Walk-Test

A zone “Walk-Test” mode has been activated.

End Test

End Test

Test has been ended.

Cross-Trip

Cross Trip

The first zone of a cross zone has been tripped
(log only).

Expansion
Event

Expansion
Event

An expansion module created an undefined
event.

Partial Arm

Partial Arm

Reports a closing in the stay mode.

Listen In

Listen In

A listen in function has been activated.

Service Start Service Start

Technician is on site.

Service End

Service End

Technician is off site.

Code Entry

Code Entry

A code has been entered.

First Open

First Open

Reports when the first partition is disarmed.

Last Close

Last Close

Reports when the last partition is armed.

Sprnklr

Sprinkler

Instant sprinkler supervisory report

Clock Set

Clock Set

Clock has been reset.

RF Jammed

RF Jammed

A wireless expansion module is jammed

CleanMe

CleanMe

A smoke detector requires cleaning.

Summary of Contents for NX148-E



























Reviews: