11
LOCATIONS 028-031: PROGRAMMING THE "GO TO PROGRAM" ACCESS CODE
Locations 028-031contain the "Go To Program" access code. Location 028 contains the first digit of the code and
location 031 contains the fourth digit of the code. THE CODE MUST CONTAIN FOUR (4) DIGITS. With the Ranger
8600E disarmed, the "Go To Program" access code can be used to enter the program mode. To disable the "Go To
Program" access code, program a "15" in location 028. The factory default setting is [9][7][1][3].
LOCATIONS 032-074: REFER TO PAGE 9 (REQUIRED FOR CENTRAL STATION REPORTING)
LOCATION 075: PROGRAMMING THE ENTRY DELAY TIME
Location 075 contains the number of 10-second increments in the entry delay. The entry delay can be programmed in
10 second increments from 10 to 150 seconds ("1" = 10 seconds through "15" = 150 seconds). For example,
programming a "2" in this location will produce an entry delay of 20 seconds. (Note: A "0" entry is treated as 0
seconds). Programming a "6" in this location will produce an entry delay of 60 seconds. Factory default is 30 seconds.
LOCATION 076: PROGRAMMING THE EXIT DELAY TIME
Location 076 contains the number of 10-second increments in the exit delay. The exit delay can be programmed in 10
second increments from 10 to 150 seconds ("1" = 10 seconds through "15" =150 seconds). For example,
programming a "2" in this location will produce an exit delay of 20 seconds. (Note: A "0" entry is treated as 0
seconds). Programming a "6" in this location will produce an exit delay of 60 seconds. Factory default is 60 seconds.
LOCATION 077: PROGRAMMING THE SIREN SHUTDOWN/RECYCLE TIMEOUT
Location 077 contains the number of 2-minute increments in the automatic cutoff time. The automatic cutoff time can
be programmed in 2 minute increments from 2 to 30 minutes ("1" = 2 min through "15" = 30 min). For example,
programming a "2" in this location will produce an automatic cutoff time of 4 minutes. Programming a "6" in this
location will produce an automatic cutoff time of 12 minutes. NOTE: This location shall be programmed for a
minimum of 4 minutes on UL Listed systems.
LOCATIONS 078-083: PROGRAMMING THE ZONE TYPES
Locations 078 through 083 contain a number identifying the characteristics of each of the 6 zones. Location 078
corresponds to zone 1 and location 083 corresponds to zone 6. Each zone will factory default according to the
programming worksheet. To program zone characteristics other than the default values, program a number from "1" to
"9" based on the zone types available in Table 1.2.
LOCATIONS 084-085: RESERVED
TABLE 1.2
DATA
AVAILABLE ZONE TYPES
"1"
DAY ZONE - When armed, a trip produces an instant alarm. When disarmed, a trip activates the keypad
sounder.
"2"
24 HOUR - A trip on a 24-hour zone produces an instant alarm when armed or disarmed.
"3"
ENTRY/EXIT - A trip will start entry delay. The lack of a trip during exit delay will enable the Automatic
Bypass or Instant mode if so programmed.
"4"
INTERIOR DELAY - A trip on Interior Delay zone will initiate an entry delay. It will be ignored during exit
delay and when disarmed .
"5"
INTERIOR FOLLOWER - Interior zone that follows the delay zones. It is instant during non-delay times. It
can be bypassed before arming, or by allowing it to automatically be bypassed in the Automatic
Bypass/Instant mode if so programmed.
"6"
INSTANT - Produces an instant alarm if tripped when armed. Ignored when disarmed.
"7"
24-HOUR SILENT - A trip on a 24-hour silent zone will communicate to the central station when the Ranger
8600E is armed or disarmed.
"8"
FIRE (PRIORITY WHEN AHJ HAS NOT APPROVED) - A short on a FIRE zone (non-bypassable) will
communicate to the central station when the Ranger 8600E is armed or disarmed. An open will create a
Trouble condition. Keypad LED will be steady for FIRE, and flashing for Trouble.
"9"
SECONDARY DELAY - A secondary delay zone works like an entry/exit delay zone, but has its own
independent delay time (see locations 178-179).
"10"
SUPERVISED 24 HOUR SILENT - A trip on a Supervised 24-hour silent zone will communicate to the central
station when the 8600E is armed/ disarmed and give LED indication of the zone(s) faulted.
