27
LOCATION 250-251: RESERVED
LOCATION 252-253: PROGRAMMING TO REPORT KEYPAD AUXILIARY 3
The Ranger 8600E has the ability to report a Silent Auxiliary 3 code each time the [7] and [9] keys are pressed
simultaneously on the keypad. The desired Auxiliary 3 code is programmed in locations 252-253. If both locations are
"0", the Auxiliary 3 double keypress is disabled. Location 252 contains the standard digit, and location 253 contains the
extended digit. When using 4+2 format, the number programmed in location 252 is sent as the "ones" digit. The "tens"
digit is programmed in location 253.
LOCATION 254: PROGRAMMING TO "USER ON SITE"
The 8600E has the ability to send a "user on site" report by entering [
U
] - [0], followed by a valid arm/disarm code at the
keypad when the system is not armed. This can be used to log the return of latch key kids or the presence of
employees. The desired "user on site" code is programmed in location 254. If this location contains a "0", "user on site"
report will not be sent. When using 4+2 format, the number programmed in this location is sent as the "tens" digit. The
"ones" digit is automatically the man number. When using the remote arming input, the man number is 1. When using
a one button "Quick Arm" code the man number is 1.
LOCATION 255: PROGRAMMING THE CROSS ZONE TIME
Location 255 contains the number of minutes (1 to 15) in which a second trip must occur in a cross-zone before an
alarm is created. Care must be taken when activating this feature that two or more cross-zones are set up that will be
tripped within this time frame in the event of a burglary. This feature should only be used on interior zones. Never
activate cross- zoning on a perimeter zone.
THE REMAINING LOCATIONS ARE ACCESSIBLE ONLY THROUGH DOWNLOADING!
LOCATIONS 256-263: CONTROL PANEL ACCESS CODE
Locations 256-263 contain the eight digit access code the 8600E must receive from the downloading software before
the panel will permit downloading to occur. The factory default code is listed in the instructions provided with the CADDX
download software package.
LOCATIONS 264-279: CALL BACK TELEPHONE NUMBER
The presence of a phone number in locations 264-279 will cause the control panel to dial back this number after a
successful panel access code has been entered. If a telephone number is present, the control panel will hang up for
approximately 36 seconds (insuring that the calling party has disconnected), then it will call back. Any zero (0) within the
telephone number must be programmed as an "A". If tone dialing is desired, program an "F" in the location where tone
dialing should begin. If the entire number should be tone dialing, program an "F" in location 264. Four-second delays
can be obtained anywhere in the sequence by programming a "D" in the appropriate delay location. WARNING: THE
CALLBACK PHONE NUMBER SHOULD ALWAYS BE REVIEWED FOR ACCURACY BEFORE DISCONNECTING.
LOCATION 280: ANSWERING MACHINE DEFEAT
Location 280 contains the answering machine defeat enable. To defeat an answering machine, two telephone calls
must be made to the premises. On the first call, let the phone ring the same number of times (or less) as the number
programmed in this location (maximum 3). The control panel will detect these rings and start a 45-second timer. If a call
comes in during that 45-second time frame, the control panel will answer on the first ring. To disable this feature,
program a "0" in this location. If anything is programmed in location 197, it will override this location.
LOCATION 281: LOCAL PROGRAMMING LOCKOUT
Location 281 is used to disable local programming lockout. If a "5" is programmed in this location, all local programming
is locked out. If an "A" is programmed in this location, all programming functions related to the digital communicator will
be locked out. Any other number in location 281 will allow all local programming.
LOCATION 282: CONTROL PANEL SHUTDOWN
Location 282 is used to shut down the control panel. Programming an "A" in this location will completely shutdown the
control panel. The keypad will appear "dead", and the siren and communicator will not operate. WARNING: EXTREME
CARE SHOULD BE TAKEN NOT TO INADVERTENTLY PROGRAM THIS LOCATION.
