Cadel Martina Installation, Use And Maintenance Handbook Download

Page: 76 / 96

Pag. 76

MARTINA-SOLARIS-ALESSIA-VANESSA

5.3.

START-UP

To  start  the  stove,  hold  down  button  P4  for  a  few  seconds;  the  words  “Fan  Cand”  will  appear,  the
extraction device will go on at minimum and the heating element will begin preheating. After this stage,
which  lasts  around  2  minutes,  the  words  “Load  Wood”  will  appear  and  the  auger  will  begin  loading
pellets  while  the  heating  elements  continues  to  preheat.    When  the  temperature  read  by  the  fumes
probe is high enough,  the electronic  control  unit considers ignition  to  have  taken place (approx.  7-10
minutes)  and  goes on  to  the  next stage  of  flame stabilization;  the  words  “Fire  On”  will appear on  the
display.  At the end of the “Fire On” stage the control unit goes into working mode and shows the power
and ambient temperature.  At this stage output can be regulated from 1 to 5 by means of buttons P5 and
P6.

5.4.

FLAME REGULATION

Picture 12

5.5.

FAILED IGNITION

If the pellets do not ignite, failed ignition will be indicated by an alarm “AlAr no Fire”. The stove ignites in
about  7/10  minutes  if  top  grade  pellets  are  used  in  an  ambient  temperature  of  about  10°C.  If  the
ambient  temperature  is  lower  the  spark  plug  cannot  ignite  the  stove  and  needs assistance  by  placing
some pellets in the burn pot with a piece of burning firelighter on top (e.g. firelighters cubes).

ATTENTION: after failed ignition the accumulated pellets in the

burn pot MUST BE CLEARED OUT

before re-igniting the stove

Too  many  pellets in  the  burn pot, damp pellets,  or  a  dirty burn pot, make  ignition  difficult and cause
dense  white  smoke  to  form,  which  can  be  harmful  to  health  and  cause  explosions  in  the  combustion
chamber.  It is therefore necessary not to stand in front of the stove when dense white smoke appears at
the ignition stage.

ATTENTION:

if after some months the flame is weak and/or orange coloured, the glass tends to

easily become black, and the burn pot tends to get thick deposit on it, clean the stove (see

chapter

7, pages 81 and following

), stovepipe and flue.

5.6.

POWER FAILURE

When the stove goes on again after an electricity black-out it shows “AlAr no rEtE” and the extractor will
expel residual smoke for 15 minutes and start the turning off process. Reset the error pushing ON/OFF
button. When it has cooled, empty the burn pot and re-start the stove.

5.7.

TEMPERATURE SETTING

To alter the ambient temperature setting, press button P3 and at the same time adjust with buttons P1
and P2. The temperature selected and ambient temperature will be shown on display B. If the value of
ambient temperature exceeds the limit established by the temperature setting keypad, the power goes to
minimum until the threshold is within the preset value, when “r IS” will appear on the display.

After  ignition  the  flame  can  be  regulated
through  a  Ø40mm  PVC  cap  fitted  to  the
combustion air inlet pipe.
If  the  flame  is  weak  and/or  orange  coloured,  it
means  that  combustion  is  not  perfect  and  the
baffle  must  be  opened.  The  first  time,  regulate
with the assistance of the specialized fitter. Every
time  different  grade  pellets  are  used  it  will  be
necessary to regulate.