background image

PLUMBING CONNECTION FOR SELF-CLEANING HOODS 

The  self-cleaning  hood  series  is  equipped  with  a  3/8"  compression  brass  fitting  for  each  hood 
section. The hoods are equipped with a 2" female NPT drain connection.

ELECTRICAL FITTINGS 

Hoods are frequently equipped with lights. Depending on the type of product, lighting is pre-wired 
per hood section to a junction box. Some models require connecting each light fixture separately. 
Refer to the diagram on the manufacturing drawings to ensure that the wiring is done properly. 

TOP ACCESS TO HOODS 

Provide  access  to  the  top of the  hoods  for  maintenance,  electrical fittings,  control  components, 
plumbing connections and fire protection system components, even after construction is complete. 

SILICONE 

Once the hood is in place, it is recommended to seal the various hood sections or between the hood 
and the walls with silicone. 

Recommended silicone: Kason RubbaSeal aluminum color 

PARASISMIC 

It is the responsibility of the purchaser to follow seismic installation requirements as defined by 
an engineer specializing in this type of installation.

FIRE PROTECTION SYSTEM  

According  to  NFPA  96  standard,  using  this  type  of  hood  over  cooking  appliances  requires  the 
installation of a fire extinguishing system for the exhaust ducts and the cooking appliances. This 
system is operated by fuses or thermal sensors built into the hood. In case of fire, the air intake is 
maintained and the blower is interrupted. The filter casings, ductwork and cooking surfaces are 
sprayed  with  a  chemical.  Gas  and  electricity  supply  to  the  cooking  appliances  and  the  lighting 
under the hood are cut-off and an alarm sounds. 

11 

Summary of Contents for STADIUM Series

























Reviews: