background image

4

Installation Preparation

FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before 

beginning installation.
Do not use an extension cord or adapter plug with this appliance.

WARNING

The improper connection of the equipment grounding conductor can result in a risk 
of electric shock. Check with a qualified electrician or service representative if you 
are in doubt that the appliance is properly grounded.

WARNING

PREPARE ELECTRICAL WIRING

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are adequate and in conformance 
with the National Electric Code, ANSI/NFPA 70 – latest edition, and all local codes 
and ordinances.

This appliance must have:

• 120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused electrical supply.
• Wiring must be 2 wire with ground and rated for 75°C (167°F).
• If the electrical supply does not meet the above  requirements, call a licensed 

electrician before  proceeding.

It is recommended to have:

• A circuit breaker or time-delay fuse.
• A properly grounded individual branch circuit.

Grounding Instructions–Permanent Connection

This appliance must be connected to a grounded metal, permanent wiring system, 
or an equipment-grounding conductor must be run with the circuit conductors and be 
connected to the equipment-grounding terminal or lead on the appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a malfunction or breakdown, 
grounding will reduce the risk of electric shock by providing a path of least resistance 
for electric current. This appliance is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must be plugged into an 
appropriate outlet that is installed and grounded in accordance with all local codes 
and ordinances.

For models equipped with power cord: 

Do not modify the plug provided with 

the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified 
technician.

WARNING

La conexión inadecuada del conductor de conexión a tierra del equipamiento puede 

SURYRFDUXQULHVJRGHGHVFDUJDHOpFWULFD&RQVXOWHDXQHOHFWULFLVWDFDOL¿FDGRR

representante de servicio técnico si tiene dudas sobre la correcta conexión a tierra 
del aparato.

ADVERTENCIA

Con los modelos equipados con cable de corriente:

 No modifique el enchufe 

provisto con el electrodoméstico; si no coincide con el tomacorriente, solicite la 
instalación de un tomacorriente apropiado a un electricista calificado.

ADVERTENCIA

PARA SEGURIDAD PERSONAL: Quite el fusible o abra el interruptor de circuitos 
antes de comenzar la instalación. No utilice un cable de extensión o un enchufe 
adaptador con este artefacto.

ADVERTENCIA

Summary of Contents for CDD420P2TS1

























Reviews: