background image

4

1.1  General warnings

 -

  This instruction is an integral part of the booklet of 

the appliance on which the kit is installed. Please consult 
this booklet for general warnings and fundamental safety 
rules.

 -

  This manual is designed only for the qualified 

and authorised installation technician, who must be 
sufficiently trained and in possession of all psycho-
physical requirements as per the law. 

 -

 

All operations must be carried out with care and 
according to best practices, and in compliance with 
workplace safety regulations.

 -

  After unpacking, check that the contents are intact 

and that all parts are included. If not, contact the agent 
who sold the appliance to you.

 -

  It is forbidden to modify the safety or adjustment 

devices without authorisation from and indications of the 
manufacturer.

 -

  It is forbidden to dispose of, or leave in the reach of 

children, the packaging materials which could become 
a source of danger.

 -

  Repairs or maintenance must be performed by the 

Technical Assistance Service or by qualified personnel 
in accordance with this manual. Do not modify or tamper 
with the appliance as this could create dangerous 
situations and the manufacturer will not be liable for any 
damage caused.

GENERAL

Summary of Contents for 010 LCD 2T

















Reviews: