background image

 2 18/10/18

UKUNDA

SIG AH 

Heat Recovery unit 

 Installation-Operation-Maintenance

 reserves the right to change the specifications of the product  at any time without prior notice

High efficiency heat recovery ventilation units Installation-Operation-Maintenance 

Manual

This manual is part of the product and must be deliv-

ered with the ventilation unit.

This appliance is not intended for use by persons (in-

cluding  children)  with  reduced  physical,  sensory  or 

mental capabilities, or lack of experience and knowl-

edge. 

Children must be supervised.

The manufacturer will not be liable for damages re-

sulting from the failure to observe the safety instruc-

tions or improper use and or installation. 

In the event of failure of the appliance and/or break-

age of any of its parts, deactivate it by disconnecting 

it from the

electrical supply, and refrain from any attempt repair-

ing the unit and call for a qualified technician and orig-

inal spare parts. 

It is responsibility of the installer to ensure that all of 

the equipment is installed in compliance with the man-

ufacturers  recommendations  and  with  current  local 

1.0 INTRODUCTION

1.1 PRODUCT DESCRIPTION

legislation and codes of practice.

If these guidelines are not followed, the unit may experi-

ence a shortened life or may present a risk of unsafety.

To guarantee efficiency and long working life, a unit in-

spection/maintenance should be carried out annually by 

an expert technician.

The  high  efficient  hear  recovery  unit  is  ideal  for  all  re-

quirements in restaurants, offices meeting rooms, class-

rooms, shops and warehouses.

The layout shall take into account the space necessary 

for installation of the unit and mainteinance/service pur-

poses, consider the possible noise generation too.

The unit is for indoor installation only

The  energy-recovery  technology  uses  the  heat  of  the 

stale indoor air to be expelled in order to either heat the 

incoming fresh air to a temperature much closer to the 

existing indoor air. 

ATTENTION : 

spigots and rectangular connections  are not delivered 

 

The basic unit includes the following  separate parts:

Ⓐ  

1x unit  complete with filter set

 

Ⓑ 

1x manual

Ⓒ 

1x touch screen controller

Ⓓ 

2x spigot adapters (connections are not included)

ATTENTION : 

spigots and rectangular connections  are not delivered

Summary of Contents for UKUNDA

















Reviews: