2017 Fitness Spa
LTR20171005, Rev. D
Operating
Your Spa
www.calspas.com
14
Ready-in-Rest Mode
READY/REST appears in the display if the spa is in Rest Mode and Jet 1
is pressed. When the spa is being used, it will heat to set temperature.
While Pump 1 High can be turned on and off, Pump 1 Low will run until
set temperature is reached, or 1 hour has passed. After 1 hour, the system
will revert to Rest Mode. This mode can also be reset by entering the Mode
Menu and changing the Mode.
Freeze Protection
If you live in an area that experiences extreme freezing weather, you need to know how to how to set your
spa to prevent freeze damage. Some spa owners choose to drain and winterize their spas, but others prefer
to keep it filled and operating. If you don’t want to drain your spa, you can continue to run it safely through
the winter, providing you program it correctly.
When you expect the temperature to approach freezing, always keep the spa in READY Mode. As long as the
spa is in READY Mode, it will regularly check the water temperature (known as “polling”) and circulate water
every 1/2 hour.
When the sensors within the heater detect water temperature has dropped to 42°F (5.5°C), then the pumps
and the blower automatically activate to provide freeze protection. The pumps and blower will run either
continuously or periodically depending on conditions.
Press Jets 1
REST
RANGE
Main Screen
READY/ REST RANGE
Then
Press
Press
Once
Twice
Setting the Heat Mode
Main Screen
READY
RANGE FLTR1
READY
SET
SET
REST
Toggle between
READY and REST
There are two heat modes: READY Mode and REST Mode.
READY Mode:
In order for the spa to heat, a pump needs to circulate water
through the heater. The pump that performs this function is known as the
“heater pump.”
The heater pump can be either a 2-Speed Pump 1 or a circulation pump. If the
heater pump is a 2-Speed Pump 1, READY Mode will circulate water every 1/2
hour, using Pump 1 Low, in order to maintain a constant water temperature,
heat as needed, and refresh the temperature display.
This is known as “polling.”
REST Mode:
REST Mode will only allow heating
during programmed filter cycles. Since polling does not
occur, the temperature display may not show a current
temperature until the heater pump has been running
for a minute or two.
Setting the time of day is important for determining filtration times and other
background features. 24-hour time display can be set under the PREF menu.
Then
Press
Press
Once
3X
Setting Time
Note: This system does NOT display the time of day . The default
display on the Main Screen is the current water temperature .
Displaying time of day is not a selectable feature .
SET
P
SET
P
SET
P
SET
P
READY
RANGE FLTR1
Set hour
Set minutes
Main Screen
Summary of Contents for F-1222
